This product is Listed to applicable UL
®
Standards and requirements by Underwriters Laboratories
Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION
: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE
: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference and (2) this device must
accept any interference, including interference that may cause undesired operation of the device radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
Crestron Electronics, Inc.
Installation Guide - DOC. 7936C
15 Volvo Drive, Rockleigh, NJ 07647
(2048522)
Tel: 888.CRESTRON
06.18
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pasproduire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner
avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication
satisfaisante.
To satisfy RF exposure requirements, this device and its antenna must operate with a separation
distance of at least 20 centimeters from all persona and must not be colocated in conjunction with any
other antenna or transmitter.
The product warranty can be found at
www.crestron.com/warranty
.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents
.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo, infiNET EX, and Z
ū
m are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Bluetooth is either a trademark
or registered trademark of Bluetooth SIG, Inc. in the United States and/or other countries. UL and the
UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the
United States and/or other countries. Wi-Fi is either a trademark or registered trademark of Wi-Fi
Alliance in the United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2018 Crestron Electronics, Inc.
Specifications
NOTE
: “Z
ū
m Net” refers to the wireless mesh network that connects one or more rooms with a Z
ū
m Floor Hub, and consists of one Z
ū
m Net Wireless Gateway and one or more Z
ū
m
Network Bridges. Each Z
ū
m Network Bridge functions as a routing node, which relays the signals it receives on to any other Z
ū
m Net devices within range. This effectively extends the
total range of the network and provides multiple redundant signal paths for extra reliability. A maximum of six “hops” across routing nodes is allowed, although a maximum of three is
recommended. Up to 100 Z
ū
m Net devices are permitted per gateway, although best practices suggest a limit of 50. Refer to the “Installation and Setup of Crestron RF Products” Best
Practices guide (Doc. 6689) at
www.crestron.com/manuals
for more information.
NOTE
: Do not stack multiple gateways.
SPECIFICATION
DETAILS
Supported Devices
Z
ū
m Net Devices
Maximum Devices Allowed
Supports Crestron Z
ū
m Net wireless devices only
Supports up to 100 Z
ū
m Network Bridges per Z
ū
m Net Gateway
Wireless Communications
RF Transceiver
Range
Z
ū
m Net 2-way RF, 2.4 GHz ISM Channels 11-26 (2400 to 2483.5 MHz), default channel 15, IEEE 802.15.4 compliant
50 ft (15 m) to nearest Z
ū
m Net mesh network device(s), subject to site-specific conditions and individual device capabilities,
range between floors or ceilings is limited to one level
Wired Communications
Ethernet
USB
10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3at Type 1 compliant
USB device port for setup
Power
Power over Ethernet (PoE)
Power Pack
Power Consumption
IEEE 802.3at Type 1 (802.3af compatible) Class 1 (3.84 W) PoE powered device;
Maximum distance is 100 meters (328 feet)
0.75 A (minimum) @ 24 VDC;
100-240 VAC, 50/60 Hz power pack,
model PW-2407WU not included
2.1 watts typical
Environmental
Temperature
Humidity
Heat Dissipation
41° to 104 °F (5° to 40 °C)
10% to 90% RH (non-condensing)
7 Btu/h
Construction
Enclosure
Mounting
IFE small form factor, black and blue plastic
Freestanding, surface mount, or 35 mm DIN EN 60715 rail mount;
Occupies 8 DIN module spaces (144 mm); Surface/DIN rail mounting bracket included, optional rack mount and pole mount
kits not included
