background image

DO

 

GUIDE

TSW-550/750/1050-TTK and TSW-550/750/1050-SMK

 

TableTop Kits and Swivel Mount Kit for TSW-550, TSW-750, and TSW-1050

The Crestron

®

 TSW-550-TTK, TSW-750-TTK, and TSW-1050-TTK are functionally identical. For 

simplicity within this guide, the term “TSW-550/750/1050-TTK” is used except where noted.

DO

 Prepare the TSW-550/750/1050-TTK

The TSW-550/750/1050-TTK comes with parts for routing device cabling through either the rear of 
the unit or through the bottom for a neat appearance.

Route Cable through the Bottom of the TSW-550/750/1050-TTK

Out of the box, the TSW-550/750/1050-TTK comes with a plastic cover on the rear of the unit, 
allowing the LAN cable to pass out through the bottom, such as when the TSW-550/750/1050-TTK is 
attached to the TSW-550/750/1050-SMK Swivel Mount Kit (sold separately).

Route Cable through the Rear of the TSW-550/750/1050-TTK

For routing a single CAT5 cable through the rear of the TSW-550/750/1050-TTK, the plastic cover on 
the rear must be replaced with the included strain relief. To replace the plastic cover with the strain 
relief, perform the following procedure:

1. Remove the two screws on the bottom of the unit that hold the metal bracket inside the  

TSW-550/750/1050-TTK. Then, remove the metal bracket.

2. With the metal bracket removed, pull downward on the plastic cover to remove it from the  

TSW-550/750/1050-TTK.

3. Insert the LAN cable through the opening on the rear of the TSW-550/750/1050-TTK and attach 

the strain relief to the cable.

4. Attach the strain relief by pushing it upward into the slot on the rear of the  

TSW-550/750/1050-TTK.

NOTE:

  For added security in mounting the touch screen, refer to “DO Use the Security Option” 

and follow that procedure from this point. For standard mounting, continue with the following 
step.

5. Reinstall the metal bracket using the screws removed in step 1.

DO

 Mount the Touch Screen in 

the TSW-550/750/1050-TTK

Connect the LAN cable to the touch screen and 
gently pull excess cable out through the rear of  
the TSW-550/750/1050-TTK to ensure the touch 
screen is seated completely into the  
TSW-550/750/1050-TTK and that the touch  
screen’s magnets engage the metal bracket.

DO

 Assemble the  

TSW-550/750/1050-SMK

Assemble the Swivel Mount

To assemble the swivel mount, perform the  
following procedure:

1. Attach and secure the swivel mechanism tube 

to the bottom of the TSW-550/750/1050-TTK 
using the three 06-32 x 3/16” screws included 
with the TSW-550/750/1050-TTK.

2. Remove the paper liner from the felt washer and attach the washer to the bottom of the swivel 

mechanism tube.

3. If the cable is routed to exit through the bottom of the TSW-550/750/1050-TTK, feed the full 

length of the cable through the swivel mechanism tube.

4. Use the included template to prepare the mounting surface. The center hole diameter for the 

swivel mechanism tube should be 7/8” (22 mm) minimum, 15/16” (24 mm) maximum. Position the 
template so the edge indicated as the front edge of the table or surface aligns with the desired 
front position of the TSW-550/750/1050-TTK. Observe the dashed line indicating the front edge 
of the TSW-550/750/1050-TTK to ensure the device does not overhang the mounting surface.

5. Using the six mounting holes on the swivel stop plate as a template, drill pilot holes in the 

mounting surface. The holes should be 0.093” (2 mm) minimum diameter, 0.115” (3 mm) 
maximum diameter, and no deeper than 0.35” (9 mm).

6. Attach the swivel stop plate to the bottom of the mounting surface using the six included 08-8B 

x 1/2” screws.

7. Pass the swivel mechanism tube down through the mounting hole and swivel stop plate.

NOTE:

  The swivel stop plate has a permanently installed limiting screw to prevent the swivel 

mechanism from spinning continuously in one direction and tangling the cable attached to the 
touch screen.

8. Slide the included hardware up onto the swivel mechanism tube in the order indicated in the 

illustration that follows.

NOTE:

  The keyed metal washer fits onto the swivel mechanism tube in one of two orientations: 

facing toward or facing away from the permanently installed limiting screw in the swivel stop 
plate. Orient the tab on the washer to face away from the permanently installed limiting screw.

9. Adjust the tightness of the 7/8”-14 nut to achieve the desired resistance in swivel assembly 

motion. A flat tool, such as a large flat head screwdriver, may be used in the slot on the bottom 
of the swivel mechanism tube to hold the tube still while tightening the nut.

Metal Bracket

Plastic Cover

Remove these screws 
to release the metal bracket. 

Pull downward on the 
plastic cover to remove it.

Push the strain 
relief upward to 
attach it.

Cutout

TSW-750-TTK

Swivel Mechanism Tube

Screws (3) 06-32 x 3/16”

Felt Washer

Swivel Mechanism Tube 

Slot in Tube

Table or Mounting Surface (Front Edge) 

Mounting Holes (6)
in Swivel Stop Plate 

Swivel Stop Plate

Screws (2) 08-32 x 1/8” 

Bottom Side of Table or Mounting Surface 

Screws (6) 08-8B x 1/2” 

Cork and Rubber Washer

Keyed Metal Washer

Rubber Washer

Steel Washer

Nut 7/8”-14 

Mounting Hole

Permanently Installed
Limting Screw 

DO

 Check the Box

QUANTITY

PRODUCT

COLOR

PART NUMBER

Items for TSW-550/750/1050-TTK Only

1

Plastic Strain Relief

1

Black

2033955

1

Plastic Strain Relief

2

Gray

2033954

1

Overlay Cutout Template

4517324

2

Screws, 04-20 x 5/8"

2007139

Items for TSW-550/750/1050-SMK Only

1

Swivel Stop Plate

4504353

1

Keyed Metal Washer

4506321

1

Cork and Rubber Washer

2017614

1

Rubber Washer

2017615

1

Overlay Cutout Template

4517324

1

Felt Washer

2024711

2

Screws, 08-32 x 1/8"

2017634

1

Steel Washer

2017633

1

Nut, 7/8"-14

2017632

6

Screws, 08-8B x 1/2"

2017784

3

Screws, 06-32 x 3/16"

2007202

1. This part ships with the TSW-550-TTK-B-S, TSW-750-TTK-B-S, and TSW-1050-TTK-B-S. 
2. This part ships with the TSW-550-TTK-W-S, TSW-750-TTK-W-S, and TSW-1050-TTK-W-S

Отзывы: