Assembling the Buttons
The GLPP-KP comes preassembled with a rocker button. If necessary, the rocker can be
replaced with the four included buttons. If the rocker is going to be used, skip to "Installing
into Single Gang Box." Otherwise, assemble the keypad as described in the following steps.
Refer to the accompanying illustrations.
Installing into Single Gang Box
Follow the procedure below to install the GLPPA-KP into a single gang electrical box. Refer
to the illustration below for details.
1. Make sure the keypad is oriented properly (note the location of the LED).
2. Place the GLPPA-KP into the electrical box.
CAUTION
: Excess wire pinched between the keypad and electrical box could short out.
Make sure all excess wire is completely inside the electrical box and not between the box
and the keypad.
3. Attach it to the electrical box using the included #6-32 x 3/4" screws.
1. Remove the button assembly by squeezing the sides of the bezel near the bezel snaps.
2. Remove the button from the front of the button assembly. Insert the new buttons
through the front of the bezel and snap into place.
3. Attach button assembly to the device. Ensure that the LED is on the left side.
4. Attach the desired decorator style faceplate (not supplied).
Squeeze at Arrow
Points and Pull to
Remove Button
Assembly
Gently Spread
Frame Apart to
Remove and
Install Buttons
(2) #6-32 x 3/4 in
Screws
Single Gang
Electrical Box
(Not Supplied)
Wall
GLPPA-KP
ALL ON
SCENE1
SCENE 2
ALL OFF
OFF*
ALL OFF
FULL ON
FULL ON
FULL ON
FAST OFF
FULL ON
OFF*
FAST OFF
RAISE
LOWER
RAISE
LOWER
Button Hold
Button Tap
Button Double Tap
The illustrations to the left show the default functions
available for each physical button configuration and
tap/hold actuation sequence. Tap, double tap, and hold
activate various scenes depending on the GLPP-SW
and GLPP-DIM settings. To determine scene settings,
refer to the GLPP installation guides at
www.crestron.com/manuals.
Button Tap
If using the single button rocker for a GLPP-DIM, tap
the top of the button for scene 1; tap the bottom of the
button for all off. If using the single button rocker for a
GLPP-SW single button rocker, tap the top of the
button for on and the bottom of the button for off.
For a four button configuration using a GLPP-DIM or a
GLPP-SW, tap the first button for all on, the second
button for scene 1, the third button for scene 2, and the
last button for all off.
Button Double Tap
For double-tapping functions, tap the button twice
within 0.5 seconds. If using the single button rocker for
a GLPP-DIM, double tap the top of the button for full
on; double tap the bottom of the button for fast off. If
using the single button rocker for a GLPP-SW, double
tap the bottom of the button for off. Double tapping the
top of the button provides no function.
For a four button configuration using a GLPP-DIM or a
GLPP-SW, double tap the first through third buttons for
full on and the last button for fast off.
Button Hold
For holding functions, hold down the button for more
than 0.5 seconds. If using the single button rocker for a
GLPP-DIM, hold the top of the button to raise; hold the
bottom of the button to lower. If using four buttons, hold
the first button to raise and the last button to lower.
Buttons on a GLPP-SW have no functions when held.
*Applicable to GLPP-SW only.
SCENE1
ON*
DEFAULT BUTTON FUNCTIONS
Return and Warranty Policies
Merchandise Returns / Repair Service
1. No merchandise may be returned for credit, exchange, or service without prior authorization
from Crestron. To obtain warranty service for Crestron products, contact an authorized
Crestron dealer. Only authorized Crestron dealers may contact the factory and request an
RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of
the problem, name and phone number of contact person, RMA number, and return address.
2. Products may be returned for credit, exchange, or service with a Crestron Return
Merchandise Authorization (RMA) number. Authorized returns must be shipped freight
prepaid to Crestron, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA
number clearly marked on the outside of all cartons. Shipments arriving freight collect or
without an RMA number shall be subject to refusal. Crestron reserves the right in its sole
and absolute discretion to charge a 15% restocking fee plus shipping costs on any products
returned with an RMA.
3. Return freight charges following repair of items under warranty shall be paid by Crestron,
shipping by standard ground carrier. In the event repairs are found to be non-warranty,
return freight costs shall be paid by the purchaser.
Crestron Limited Warranty
Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials
and workmanship under normal use for a period of three (3) years from the date of purchase from
Crestron, with the following exceptions: disk drives and any other moving or rotating mechanical
parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touch screen
display and overlay components are covered for 90 days; batteries and incandescent lamps are not
covered.
This warranty extends to products purchased directly from Crestron or an authorized Crestron
dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's
warranty, if any.
Crestron shall not be liable to honor the terms of this warranty if the product has been used in any
application other than that for which it was intended or if it has been subjected to misuse, accidental
damage, modification, or improper installation procedures. Furthermore, this warranty does not
cover any product that has had the serial number altered, defaced, or removed.
This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall
Crestron be liable for incidental or consequential damages of any kind (property or economic
damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any
claim made by a third party or made by the purchaser for a third party.
Crestron shall, at its option, repair or replace any product found defective, without charge for parts
or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered
only by the unexpired portion of the warranty.
Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or
implied, nor authorizes any other party to offer any warranty, including any implied warranties of
merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by
law are limited to the terms of this limited warranty. This warranty statement supersedes all previous
warranties.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, and Crestron Green Light are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or
registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries.Other
trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and
names of others.
Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
Installing GLPPA-KP into Single Gang Box
