Crestron CP3 Скачать руководство пользователя страница 9

Страница: 9 / 32

Crestron

CP3 & CP3N

3-Series Control Systems

Operations Guide – DOC. 7316C

3-Series Control Systems: CP3 & CP3N

•

CP3 Specifications (Continued)

SPECIFICATION

DETAILS

Memory

SDRAM

512 MB

Internal Flash

4 GB

Memory Card

Expandable storage up to 32 GB

(SD™ memory card not included)

External Storage

Up to 1 TB using USB mass storage device

(not included)

Communications

Ethernet

10/100 Mbps (10/100/1000 Mbps on CP3N);

auto-switching, auto-negotiating,

auto-discovery, full/half duplex, industry-

standard TCP/IP stack, UDP/IP, CIP, DHCP,

SSL, IEEE 802.1X; SNMP; BACnet/IP

;

IPv4 or IPv6, Active Directory authentication,

IIS v.6.0 Web Server, SMTP e-mail client,

installer setup via Crestron Toolbox or

MSIE

; supports all e-Control, Core 3 UI

XPanel, Crestron Mobile, Crestron Fusion™

and RoomView

applications

Control Subnet (CP3N Only)

10/100/1000 Mbps Ethernet, auto-switching,

auto-negotiating, auto-discovery, full/half

duplex, DHCP server, DNS server, port

forwarding,

Isolation

mode

Cresnet

Cresnet master mode

USB

Supports USB HID and USB mass storage

class devices via rear panel USB 2.0 host

port, supports computer console via front

panel, USB 2.0 device port

RS-232/422/485

For 2-way device control and monitoring, all

ports support RS-232 up to 115.2k baud with

software handshaking, one port also

supports hardware handshaking, RS-422,

and RS-485

IR/Serial

Supports 1-way device control via infrared

up to 1.2 MHz or serial TTL/RS-232

(0-5 volts) up to 115.2k baud

Power Requirements

Power Pack

2.0 amps @ 24 volts dc,100-240 volts ac,

50/60 Hz power pack, included

Available Cresnet Power

24 watts (1 amp @ 24 volts dc) when using

power pack

Cresnet Power Usage

15 watts (0.625 amp @ 24 volts dc) when

using Cresnet network power

Net ID

(Continued on following page)

Содержание CP3

































Результаты поиска

Содержание CP3

Отзывы:

Бренды по названию

Популярные бренды

Crestron CP3, Руководство по эксплуатации

Результаты поиска

Содержание CP3

Отзывы:

Бренды по названию

Популярные бренды