Crestron Electronics, Inc.
Installation Guide - DOC. 7334B
15 Volvo Drive Rockleigh, NJ 07647
(2033164)
Tel: 888.CRESTRON
01.14
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
Crestron
CLW-DELVEX-E/P
Wireless In-Wall Dimmer
Installation Guide
This product conforms to UL STD 1472; certified to CSA STD C22.2 No. 184.1.
FCC ID: Contains EROCWD6790
Compliance Statement (Part 15.19 )
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Warning (Part 15.21)
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF Exposure (OET Bulletin 65)
To comply with FCC's RF exposure limits for general population / uncontrolled exposure,
this transmitter must be installed to provide a separation distance of at least 20 cm from
all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter.
DESCRIPTION
The CLW-DELVEX-E/P is a 500 W in-wall dimmer and programmable keypad designed to
operate as part of a complete Crestron
®
automation system communicating via the
infiNET EX
®
wireless control network. Without the need for additional control wiring, the
CLW-DELVEX-E/P easily replaces any standard in-wall dimmer or light switch. Although
functional as a standalone dimmer, the CLW-DELVEX-E/P delivers enhanced automation
and control capability when connected to any Crestron automation control system (or any
other Creston control system) via the infiNET EX network.
Specifications
Specifications for the CLW-DELVEX-E/P are listed in the following table.
CLW-DELVEX-E/P Specifications
3. Push all power wires back into the electrical box and fasten the device to the electrical
box with the provided screws.
4. Attach decorative faceplate.
5. Ensure all buttons, including the program button, actuate without sticking.
6. Restore power at the circuit breaker.
Multigang Installations
In multigang installations, several devices are grouped horizontally in one electrical box. For
a smooth appearance, one-piece multigang faceplates (not supplied) can be installed.
NOTE
: When installing into a multigang box, do not fully tighten devices to box until
faceplate has been aligned.
The load capacity for each device in the electrical box must be derated. Refer to the
following diagrams for derating information.
Derating Information for CLW-DELVEX-E/P Dimmers
1. CLW-DELVEX-P only.
2. For details, refer to the Crestron CLW-SLVU-P Installation Guide (Doc. 7364) at
www.crestron.com/manuals.
1. CLW-DELVEX-P only.
2. The range is dependent on its placement and the building in which it is used. The construction of the building,
obstructions, and RF interference from other devices are factors determining the effective range of the unit.
Important Notes
Read before installation.
•
Codes: Install in accordance with all local and national electrical codes.
CAUTION
: TO REDUCE THE RISK OF OVERHEATING AND POSSIBLE DAMAGE
TO OTHER EQUIPMENT, DO NOT INSTALL TO CONTROL A RECEPTACLE, A
MOTOR-OPERATED APPLIANCE OR TRANSFORMER-SUPPLIED APPLIANCE.
ATTENTION
: GRADATEURS COMMANDANT UN BALLAST-AFIN DE RÉDUIRE
LE RISQUE DE SURCHAUFFE ET LA POSSIBILITÉ D’ENDOMMAGEMENT À
D’AUTRES MATÉRIELS, NE PAS INSTALLER POUR COMMANDER UNE PRISE,
UN APPAREIL OPÉRÉ DE MOTEUR OU UN APPAREIL ALIMENTÉ PAR UN
TRANSFORMATEUR.
•
Wiring: Use copper wire only. For supply connections, use wire rated for at least 75° C.
•
Lamp Type: For use with permanently installed incandescent, electronic low voltage
halogen or LED, tungsten-halogen, or dimmable CFL only.
•
Electrical Boxes: Devices mount in standard electrical boxes. For easy installation,
Crestron recommends using 3 1/2 in (89 mm) deep electrical boxes. Several devices
can be installed in one electrical box (multigang). This requires derating of the dimming
device. For a smooth appearance, one-piece multigang faceplates (not supplied) can
be installed.
•
Mechanical 3- or 4-way switches do not work with CLW-DELVEX-E/P dimmers.
•
Spacing: If mounting one device above another, leave at least 4 1/2 in (115 mm)
vertical space between them.
•
Low Voltage Applications: Use with electronic low voltage transformers only. Do not
use any magnetic low voltage transformers. Operation of a low voltage circuit with all
lamps inoperative or removed may result in current flow in excess of normal levels. To
avoid transformer overheating and premature transformer failure, Crestron
recommends the following:
> Do not operate low voltage circuits without operative lamps in place.
> Replace burned-out lamps as quickly as possible.
> Use transformers that incorporate thermal protection to prevent transformer failure
due to overcurrent.
INSTALLATION
WARNING
: Turn off power at the circuit breaker. Installing with power on can result in
serious personal injury and damage to the device.
CAUTION
: New installations should be checked for short circuits prior to installing a
CLW-DELVEX-E/P dimmer. With power off, close the circuit and restore power. If the
lights do not work or a breaker trips, check and correct the wiring or fixture (if necessary).
Install the dimmer only when the short is no longer present. The warranty is void if the
dimmer is installed and operated with a shorted load.
The following describes the installation of a CLW-DELVEX-E/P dimmer.
1. Turn power off at the circuit breaker.
2. Wire the device as shown in the following diagram.
Connection Wire Gauge
Wire Color
HOT
16 AWG
Black
NEU
16 AWG
White
LOAD
16 AWG
Red
REM
16 AWG
Blue
GND
16 AWG
Green
White (NEU)
LOAD
Green
(GND)
Red (LOAD)
Black (HOT)
HOT
120V~
Blue (REM)
To One or More
CLW-SLVU-P¹,²
(Optional)
500 W
400 W
400 W
400 W
250 W
400 W
Changing Button Assemblies
The button assembly can be removed and replaced with other button assemblies.
1. As shown in the following diagram, remove the button assembly by squeezing the
sides of the bezel near the bezel snaps.
Squeeze at arrow
points and pull to
remove button
assembly.
NOTE
: When the button assembly is removed, power to the unit and load is
removed automatically.
2. Remove button(s) from the front of the button assembly as shown in the following
diagram.
3. Insert new buttons through the front of the bezel and snap into place as shown in the
following diagram. Ensure that the LED strip is on the left side.
4. Attach button assembly to the device as shown in the following diagram. Ensure that
the LED strip is on the left side.
Gently spread frame
apart to remove
buttons.
Gently spread frame
apart to insert
buttons.
5. Once power has been restored, press and hold the right side of the air-gap switch
(program button) as shown in the following diagram. After 5 seconds some LEDs start
flashing. Continue to hold the button and proceed to step 6.
6. While holding the program button, tap all of the buttons in the new layout. The LED
next to the tapped button lights.
NOTE
: If the rocker switch is installed, press the top and bottom of the rocker.
7. After all of the buttons have been tapped, release the program button to save the
settings.
NOTE
: Changing the button configuration alters the device’s behavior. Refer to
"Default Button Functions" on the following page for details.
6
5
7
Press and hold
the program
button.
Release the
program button
to save the
settings.
Tap each of the
installed buttons
on the device.
SPECIFICATION
DETAILS
Power Requirements
120 Vac, 60 Hz
Load Types
Incandescent, tungsten-halogen, electronic low
voltage transformers for low voltage halogen or LED,
electronic CFL
Load Ratings
Minimum Load
Maximum Load
25 W
500 W (Refer to the derating chart in the “Multigang
Installations” section on this page.)
Maximum Number of
Remote CLW-SLVU-P
Devices
1
9
Environmental
Temperature
Humidity
32º F to 104ºF (0º C to 40º C)
10 to 90% RH (non-condensing)
Dimensions
Height
Width
Depth
4 1/8 in (105 mm)
1 3/4 in (45 mm)
1 13/16 in (47 mm)
Weight
5 oz (128 g)
Operating Frequency
2400 to 2483.6 MHz (802.15.4 compliant)
Operating Ranges
2
Device to Gateway
Device to Device
150 ft (45 m) indoors; 250 ft (76 m) outdoors
100 ft (30 m) indoors; 175 ft (53 m) outdoors
Default RF ID
01
Further Inquiries
To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at
1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of
Crestron worldwide offices at www.crestron.com/offices.
To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.
First-time users must establish a user account to fully benefit from all available features.
Future Updates
As Crestron improves functions, adds new features and extends the capabilities of the CLW-DELVEX-E and
CLW-DELVEX-P, additional information may be made available as manual updates. These updates are solely
electronic and serve as intermediary supplements prior to the release of a complete technical documentation
revision.
Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as
an “Addendum” in the Download column.
WARNING:
To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before
wiring!
NOTES:
Observe the following points.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• This product should be installed by a qualified electrician.
• Sensors must be mounted on a vibration free surface.
PREPARING AND CONNECTING WIRES
Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking the conductors. Twist together
the ends of the wires that share a connection. Apply solder only to the ends of the twisted wires. Avoid tinning too
far up the wires or the end becomes brittle.