Operation
The following describes the basic operation of the CAEN-BLOCK-CENCN-2-POE.
TEST Button
Press the TEST button to perform a hardware test of the device. The device reports errors
via blink patterns. The device displays error codes using the NET or MSG LED on the
interface. The LED blinks a specific pattern to indicate an error.
For example, when a 3-3 LED blink pattern occurs, the LED blinks three times, pauses for
1 second, blinks three times, pauses for 5 seconds, and then repeats until the error is
corrected. When a 2-1 LED blink pattern occurs, the LED blinks two times, pauses for 1
second, blinks once, pauses for 5 seconds, and then repeats this code until the error is
corrected.
NET LED Feedback
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:(1) This device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CAUTION
: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE
: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, and Crestron Toolbox are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL is either a
trademark or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
Crestron Electronics, Inc.
Installation & Operation Guide - DOC. 7873B
15 Volvo Drive Rockleigh, NJ 07647
(2047083)
Tel: 888.CRESTRON
12.16
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
LED PATTERN
ERROR STATE
Error code 1-1
Broken Y Wire
Error code 1-2
Short to 24 V and Y
Error code 1-3
Short to Ground and Y
Error code 2-1
Broken Z Wire
Error code 2-2
Short to 24 V and Z
Error code 2-3
Short to Ground and Z
Error code 3-1
Short Y to Z
Error code 3-2
Y and Z crossed
Error code 3-3
Y and Z unbalanced
LED PATTERN
ERROR STATE
Error code 1-1
Com issue Ethernet
Error code 1-2
Com issue NET A
Error code 1-3
Com issue NET B
Error code 2-1
Com issue Ethernet and Cresnet
Error code 2-2
POE low voltage
Error code 2-3
EXT 24V low voltage
Error code 3-1
Overload NET A
Error code 3-2
Overload NET B
Error code 3-3
Overload NET A and NET B
MSG LED Feedback
SETUP Button
Press the SETUP button to enter Autodiscovery mode via Ethernet.
RESET Button
Press the RESET button to perform a hardware reset.
