Warranty and Installation Guide
Tilt Action Flat Panel Wall Mount
BFP6T
STEP 1 – ATTACH WALL MOUNT COMPONENTS TO WALL
STEP 2 – ATTACH MOUNTING ARMS TO TV
A.
Installing in Drywall (Timber frame). See Figure 1.1.
1.
If attaching this bracket using this method, you MUST spread
the Wall Plate across 2 wall studs. Wall studs can be 450mm or
600mm apart depending upon the position of the wall and the
state you live in. Crest will not accept any damages that may
occur is only 1 stud is used.
2.
Locate centre of timber studs using stud finder.
3.
Mark a minimum of four fixing holes over stud centres using wall
plate as guide (two at either end of the mount). Ensure plate
is level.
4.
Predrill holes to a depth of 50mm using high speed 5mm drill bit.
If installing in hardwood, larger diameter and deeper holes may
be required.
5.
Attach wall plate using lag bolts (W-A) through round washers
(W-C). Do not over tighten.
1.
Lay your TV face down on something soft so as not to scratch the screen
2.
Check the back of your TV to find the appropriate mounting pattern.
3.
Sort through provide bolts M-A to M-H until you find the correct size that easily fits into the back of your TV and fits snugly (the bolt must
turn at least 3 full turns). Once you have selected the bolt then find the corresponding D washer. If no bolts fit you will need to go to your
local hardware to find the correct sized bolt and washer.
4.
Once this has been located gently put your mounting arms (B and C) on the back of the TV so that the mounting holes are showing
through the arms (see figure 2.1).
5.
If the back of your TV is curved or recessed (see figure 2.3/2.4) you will also need to use spacer M-M or M-N depending upon the amount
of space you are trying to clear. This will of course mean that you will also need to use longer screws. Remember that the bolt needs to
turn at least 3 full turns.
6.
Now using the correct mounting bolt size and length through corresponding D washers to attach mounting arms to rear of TV
(see figure 2.2). To avoid damaging TV, do not over tighten bolts. (Crest is not responsible for any damage caused by screwing the bolt too
far into the back of the TV)
7.
At this stage loosen the safety bolt at the bottom of each arm as shown in figure
B.
Installing in Masonry. See Figures 1.2 & 1.3.
1.
WARNING- ensure you have an minimum of 35mm of actual
concrete/brick thickness in the hole for the anchors. Do not drill
into mortar joints. Installer must verify that the supporting surface
will safely support the combined weight of the bracket and TV.
Crest holds no responsibility for incorrectly installed brackets.
2.
Mark a minimum of four fixing holes using wall plate as guide
(two at either end of the mount) see figure 1.2. Ensure plate
is level.
3.
Predrill holes to a depth of 60mm using 8mm masonry drill bit.
Clean out holes.
4.
Fully insert masonry anchors (W-B). Tap in with hammer if required.
5.
Attach wall plate by inserting lag bolts (W-A) through round
washers (W-C) into each masonry anchor (W-B) and tighten see
figure 1.3. Do not over tighten.
Figure 1.2
Figure 1.3
Figure 1.1
Figure 2.4
Figure 2.3
Figure 2.2
Figure 2.1
A
B
C
M-A
M-B
M-C
M-D
M-E
M-F
M-G
Wall Plate
Left Adaptor Bracket
Right Adaptor Bracket
M4 x 12mm
M4 x 30mm
M5 x 12mm
M5 x 30mm
M6 x 12mm
M6 x 35mm
M8 x 16mm
1
1
1
4
4
4
4
4
4
4
Item
Description
Qty
M-H
M-I
M-J
M-K
M-L
M-M
M-N
W-A
W-B
W-C
M8 x 40mm
D4 Washer
D5 Washer
D6 Washer
D8 Washer
ø14 x ø6 x 10mm
ø5 x ø8 x 15mm
ST8 x 63mm
Concrete Anchor
D8 Washer
4
4
4
4
4
4
4
6
6
6
Item
Description
Qty
HARDWARE KIT CONTENTS
