ODC JETPACK
O
OU
UTTD
DO
OO
ORR D
DIISSC
CO
OV
VEERRY
Y C
CRRA
AFFTT
ASSEMBLY INSTRUCTIONS
I. PONTOON INFLATION
NOTE: Use the Large Cone Adapter provided with your Pump. See figure 3b for a detail of the Valve Assembly.
Before inflation, be sure to fully seat each Valve Assembly into the Pontoon, screwing tightly by hand. When fully
seating Valve Assembly, be sure that the Valve Plate is in place around Valve Assembly and not restricting the Valve
Assembly from a full seal. After inflating, be sure to fully seat the Top Cap on to each Valve Assembly, screwing
tightly by hand. Both are required for an airtight seal.
1.
Inflate each Pontoon. The Valve is located inside the Storage Pocket of each Pontoon (see figure 3).
Inflate until firm (do not over inflate).
2. Again, be sure top Valve Cap and Valve Assembly are fully seated to achieve airtight seal
.
PONTOON DEFLATION:
Unscrew entire Valve Assembly from Pontoon.
II. ASSEMBLE FRAME
NOTE:
Your Frame assembles using (12) Short Snap Pins. Please follow instructions accordingly.
1.
Assemble Cargo Deck by sliding mesh Cargo Deck over Rear Frame Member (see figure 1) and secure using attached
Hook and Loop and Strap to Ladder Lock Fasteners.
2.
Assemble Padded Seat (see figure 1a) by strapping Padded Seat Bottom over the Seat Support Frame Member.
Seat back adjusts using Side Straps (see figure 1a)
3.
Assemble Seat Support Frame Member to Left and Right Frame Members using (4) of the Short Snap Pins
(see figures 1 and 2.)
4
. Go to
IIIIII.. A
ATTTTA
AC
CH
H PPO
ON
NTTO
OO
ON
NSS TTO
O FFRRA
AM
MEE
and finish that section before returning to #5
5.
Assemble Cargo Deck to Left and Right Frame Members using (2) Short Snap Pins (see figures 1 and 2).
6.
Assemble Foot Bar Extensions to Seat Support Frame Member. (see figure 1 and 2)
7.
AssembleFoot Bars to Left and Right Frame Members using (2) Short Snap Pins (see figures 1 and 2).
III. ATTACH PONTOONS TO FRAME
NOTE:
Always inflate the Pontoons first, before attaching to Frame.
1.
Position inflated Pontoons under the Left and Right Frame Members with ODC JETPACK
™
logos oriented to the outside.
The Frame Members fit around the Storage Pockets.
2.
Attach Pontoons to Frame as illustrated in figures 3 and 3a.
NOTE:
Be sure the Straps are pulled tight through the
Cam-lock Buckles. Frame should be positioned forward or aft on the Pontoons to achieve center of gravity for an even
ride when fully loaded on the water.
3.
Go Back to
IIII.. A
ASSSSEEM
MBBLLEE FFRRA
AM
MEE
# 5 and finish Frame assembly.
IV. OAR & OARLOCK ASSEMBLY
1.
Loosen the Wingnut on the Oarlock and slide the Oarlock onto the handle end of the Oar Shaft.
2.
Attach blade end of Oar to handle end of Oar.
3.
Place Oarlock shafts into Frame.
4.
With the Oarlocks installed on the Frame, the oars should be equally adjusted left and right allowing at least two
thumbs’ distance between the Oars, to avoid pinching your thumbs when rowing. With the blades perpendicular to
the water, tighten the Wingnuts.
V. ATTACH STRIPPING APRON TO FRAME
1.
Snap front two Straps around the Frame underneath the Oarlocks, and snap the back two Straps to the Seat Support
Frame behind the Seat Back.
TM
TM
