background image

soldering & handling

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree

®

 and XLamp

®

 are 

registered trademarks and the Cree logo is a trademark of Cree, Inc. Other trademarks, product and company names are the property of their respective 

owners  and  do  not  imply  specific  product  and/or  vendor  endorsement,  sponsorship  or  association. This  document  is  provided  for  informational 

purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com.

Cree, Inc.

4600 Silicon Drive

Durham, NC 27703

USA Tel: +1.919.313.5300

www

.cre

e.

com

/Xl

amp

C

LD

-A

P

75

 R

ev 5
G

Cree

®

 XLamp

®

 MT Family and MK Family LEDs

InTroDuCTIon

This application note applies to XLamp

®

 MT Family and MK 

Family LeDs, which have order codes in the following formats.

MTxxxx-xx-xxxx-xxxxxxxxx
MKxxxx-xx-xxxx-xxxxxxxxx

This application note explains how XLamp MT Family and MK 
Family LeDs and assemblies containing these LeDs should be 
handled during manufacturing. Please read the entire document 
to understand how to properly handle XLamp MT Family and MK 
Family LeDs.

TabLE oF ConTEnTs

Handling XLamp

®

 MT Family and MK Family LeDs ................... 2

Circuit Board Preparation & Layouts ........................................... 4
Case Temperature (T

s

) Measurement Point ............................... 5

Notes on Soldering XLamp

®

 MT Family and MK Family LeDs .. 6

Moisture Sensitivity ..................................................................... 7
Low Temperature Operation ........................................................ 7
XLamp

®

 MT Family and MK Family LED Reflow Soldering 

Characteristics ............................................................................. 8
Chemicals & Conformal Coatings ............................................... 9
Assembly Storage & Handling ................................................... 10
Tape and Reel ............................................................................. 11
Packaging & Labels ................................................................... 12

Содержание XLamp MK Series













Отзывы: