LPN00838X0004A0_A
3 of 3
www.creelighting.com
© 2020 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content
is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree
®
and the Cree logo are
registered trademarks and the Cree SmartCast Technology logo is a trademark of Cree, Inc. SmartCast
®
, is a registered
trademark of Cree Lighting, A company of IDEAL INDUSTRIES.
SCENE CONTROLLER PAIRING INSTRUCTIONS
STEP 1:
Down the free App (Search for Cree Lighting).
STEP 2:
Press & Hold (approx. 5 sec) any button until the LED flashes fast,
means switch is ready for pairing.
STEP 3:
Auto-Scan APP Pairing Method:
• Pair
• Follow on-screen steps in the app to connect to
your scene controller
• Enable Bluetooth on your device
• Guided Setup
• Follow step-by-step on-screen instructions to configure
each button
STEP 4:
Build Scene definition in App
, the user can add personal settings
to a light or group of lights by selecting CCT level, Color, or preset
Scene to a button which will synchronize with the controller. Follow
step-by-step on-screen instructions to configure each button
Reset controller,
Press & Hold (approx. 5 sec) any button until the
LED flashes fast and the Scene Controller icon is removed in the
APP, means Switch reset is finished.
CLEANING
Clean using a cloth dampened only with water and a little mild
detergent. Use of solvents or hydrocarbon-based cleaners may
cause permanent damage.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the device.
This device has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the device is operated in a commercial
environment. This device generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this device in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
In addition, this device complies with ICES-003 of the Industry
Canada (IC) Regulations.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device. In addition, this device complies with ICES-003
of the Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Wall Control Troubleshooting
Issue
Resolution
Wireless Scene Controller LED
does not blink
Check wiring
(LINE/NEUT/GND required)
Reset the controller and verify the LED flashes
fast continuously.
Wireless Scene Controller will
not join a network
Check wiring (LINE/NEUT/GND required).
Reset the controller and verify the LED flashes
fast continuously.
Replaced existing Wireless
Scene Controller and fixtures
will not turn on
Check Wiring (each fixture shall be wired with
constant HOT)
Wireless Scene Controller will
not control fixtures
Check group assignments with Configuration
Tool