Creative 1212M Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 120

background image

4 - The PatchMix DSP Mixer
Main Section

50

Creative Professional

Auxiliary Effects & Returns

f

The Wet/Dry mix

setting in the effect
should normally be set to
100% when the effect is
inserted as a sidechain
effect. This is because the
Aux Return Amount will
control the wet/dry mix.

The section immediately below the TV Screen is where you assign the Auxiliary Effects.
In a traditional mixing console, auxiliary effects sends are used to send part of the signal
to outboard effect devices, then return the effected signal back into the mix using the
effect returns. This is called a sidechain routing because the aux signal takes a detour
through the effects before being summed back into the main mix.

Sidechain effects are usually effects that you might want applied to several channels,
such as reverb. Effects such as EQ and compressors are usually NOT used as sidechain
effects because they can cause unpredictable results when returned to the main bus.

You can also use the Auxiliary Sends as two extra mix buses. By turning the Aux Return
amount all the way down and dropping an Insert Send into the chain, you can send the
Auxiliary bus to any output you wish. See

“Insert Section”

for more information.‚

Sync/Sample Rate Indicators

The Sync/Sample rate Indicators show the current session’s
sample rate and whether it is internal or slaving to an external
source. The LEDs indicate which sample rate is currently in
effect. If an external source is being used, the Source display
reads “EXTERNAL”.

When slaving to an external master source, the clock may drift
slightly or change dramatically (i.e. abrupt sample rate
change or unplugging of physical master source). PatchMix
DSP is tolerant to minor drifting within the supported rates
of 44.1k, 48k, 88k, 96k, 176k and 192k, but if the sample rate
drifts out of this range the “LOCKED” LED will extinguish.

If the external clock source makes a radical sample rate change from the lower rates of
44.1k/48k to a higher rate (or between any of the higher rates), the hardware automati-
cally switches to internal 48kHz clock until the proper external clock is restored. The
“LOCKED” LED will be off and the two units are NOT synchronized. Always check the
“LOCKED” LED when using an external clock source.

Main Bus

Side

Chain

Input

Fader

Mute

Output

Return

Amount

Send

Amount

Input

Pan

Aux

Amt

Aux

Amt

Aux Bus

Sidechain Diagram

(Post-Fader Aux Sends)

«
...
48
49
50
51
52
...
»

Содержание 1212M

























































































































Отзывы:

Нет отзывов

Похожие инструкции для 1212M

Бренд: Samsung Страницы: 36

Бренд: NEC Страницы: 174

Бренд: RBH Sound Страницы: 12

Бренд: Parklio Страницы: 29

Бренд: Dahua Страницы: 23

VTO2000A Series

Бренд: Dahua Страницы: 41

Бренд: Dahua Страницы: 18

Бренд: Dahua Страницы: 85

Бренд: NAD Страницы: 2

Бренд: salmson Страницы: 16

FINISH-OUT MC111M

Бренд: M&S Systems Страницы: 2

Бренд: M-system Страницы: 3

Бренд: ViziT Страницы: 11

Бренд: Coby Страницы: 2

UTILITY UTAC13-0

Бренд: WIA Страницы: 8

Бренд: TCS Страницы: 30

Бренд: EAW Страницы: 2

Бренд: Laser Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды