background image

WEEKLY (cont.)

Reassembling the Hoppers (PIC 1/2/3/5/6) 
(Refer to Figure I)

IMPORTANT:

All components must be completely dry prior 

to reassembly.

1. Place the drive shaft bearing inside the hopper with the 

threads going through the hole in the rear of the hopper. 

2. Secure the bearing by attaching the palnut to the bearing 

at the outside rear hopper opening. Tighten using only 
your fingers. Use one hand inside the hopper to push 
the bearing outward while turning the palnut clockwise.

3. Install the auger spring drive shaft and the auger spring 

by inserting the flat end of the spring into the hole in the 
auger drive shaft.

4. Insert assembly into the lower front hopper opening, 

making sure the threaded end of the auger spring 
drive shaft completely inserts into the drive shaft bearing 
in the rear of the hopper. The drive shaft bearing threads 
should be accessible from the outside rear of the hopper.

5. Place the washer over the drive shaft bearing threads followed by securing the drivelink onto the drive 

shaft bearing by turning counterclockwise. Secure the auger spring with one hand while attaching the 
drivelink with the other.

6. Replace the auger pinwheel making sure the pins are securely positioned inside the locator holes in 

the hopper.

7. Replace the dispense elbow in the “UP” position.
8. Fill the hopper with product and replace the cover.
9. Reinstall the hopper into the machine; making sure it is properly positioned inside the notches under 

the hopper.

10. Turn the elbow down toward the mixing funnel, keeping it lined up over the funnel opening.

Disassembling & Cleaning the Hoppers (PIC 4)

IMPORTANT: 

Do not wash hopper without first disassembling.

1. Open the door and rotate the dispense elbow on the hopper to the “UP” position to prevent spillage.
2. Remove the hopper from the cabinet.
3. Remove the hopper cover and empty hopper contents.
4. Pull off the elbow.
5. Pull off hopper base.
6. Remove the auger pinwheel by pulling it forward while stretching out the sides of the hopper (thin hopper only). 

*See below for wide hopper. 

7. Remove the coupling at the rear of the hopper by holding the auger spring with one hand at the front of the 

hopper while turning the coupling clockwise with the other hand.

8. Remove the auger with o-ring by pulling them out through the lower front opening of the hopper.
9. Remove the nuts at the front and rear of the hopper by turning counterclockwise, then remove the bearings 

from the inside of the hopper.

10. All parts in contact with food must be washed, rinsed, sanitized and air dried.

* For wide hoppers: Remove wing nut and flat washer on outside of hopper and remove pinwheel assembly (gear with
spring and pinwheel with 2 springs)

Figure I

Crathco® Powdered Beverage Dispensers

Page 9

Содержание PIC 1





































































Отзывы: