background image

1

2

3

4

5

6

1: INPUT: Connect your guitar here using a shielded instrument cable.

2: OVERDRIVE BOOST: Increases the output volume and adds “crunch” to your sound.
This control is only active when the Overdrive Gain control (#3) is turned on. For more
information please see the “Getting Your Sound” section to the right.

3: OVERDRIVE GAIN: Controls the Overdrive Boost knob (#2) and adds distortion to
your sound. This control is only active when turned on. For more information please see
the “Getting Your Sound” section to the right.

4: CLEAN VOLUME: Controls the overall output level of the amp.  For more information
please see the “Getting Your Sound” section to the right. 

5: BASS: Adjusts the low frequency output level: to the left reduces the low frequency
output; to the right increases it. 

6: MID: Adjusts the midrange frequency output level: to the left reduces the midrange
frequency output, to the right increases it. 

7: TREBLE: Adjusts the high frequency output level: to the left reduces the high fre-
quency output; to the right increases it.

8: INSERT: Connect an external effects device via this jack. Use a stereo 1/4” male Y-
cord: ring = send, tip = return, sleeve = ground. Send goes to the effect’s input; return
comes from its output. (See the illustration on the panel to the right for more information.)  

9: HEADPHONE: Plug a pair of stereo headphones  here for private listening. When this
jack is used the internal speakers and the external speaker jacks are disconnected.

10: POWER LED: This LED lights when the amplifier is powered up.

11: POWER SWITCH: Turns the amplifier on (in the UP position) and off (in the down
position).

12: AC LINE IN: (Rear panel, not shown) This heavy-duty, grounded, three-wire power
cord is to be plugged into ONLY a safely-wired, grounded 120 volt, 60 cycle AC power
outlet. DO NOT attempt to defeat the ground connection of this cable! If your EL10G was
purchased outside of the United States, see the unit’s rear panel for its power rating and
follow the above guidelines.

EL-10G Electra Series Guitar Amplifier

Содержание ELECTRA SERIES EL-10G

Страница 1: ...ries Guitar Amplifier The EL 10G features built in overdrive circuitry three bands of equalization an insert jack and a jack for headphones In order to get the most out of your new amplifier we strongly urge you to go over the information contained in this manual before you begin playing And thank you for choosing ...

Страница 2: ...t 7 TREBLE Adjusts the high frequency output level to the left reduces the high fre quency output to the right increases it 8 INSERT Connect an external effects device via this jack Use a stereo 1 4 male Y cord ring send tip return sleeve ground Send goes to the effect s input return comes from its output See the illustration on the panel to the right for more information 9 HEADPHONE Plug a pair o...

Страница 3: ...in controls at or near 10 Use the Volume con trol to set the output level TIP RING SLEEVE RETURN SEND GROUND Stereo to mono Y cord to Insert jack to Insert jack STP201 3 STP202 6 STP203 9 YPP117 1 4 TO 1 4 MONO CABLES to effect OUT jack to effect IN jack External Effect TIP RING SLEEVE Y adapter and 2 cables External Effect R ING R ING T IP T IP to effect OUT jack to effect IN jack EL 10G Electra ...

Страница 4: ...PMENT TO RAIN OR MOISTURE CAUTION NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL CAUTION OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS OPERATED AT HIGH VOLUME CAUTION RISK OF ELECTR...

Отзывы: