CraftUnique CraftBot Plus Скачать руководство пользователя

Страница: 30 / 32

Version V1.0

Page: 30 / 32

6. Troubleshooting - Electrical

Problem

Causes

Check procedures /corrective measures

The machine does

not operate when

the power switch

is turned on.

The power cord is not plugged

in properly.

Check the contact between the power plug

and the outet.

Broken power cord.

Check for continuity. If nothing, replace

the cord.

Defective power swtich.

Check for continuity across the contacts.

If nothing, replace the power switch.

Blown fuse in the power supply

unit.

Check for continuity. If nothing, remove

the cause of the fault, and replace the

fuse.

Defective power supply unit.

With AC present, check for 24V DC betwe

en the V+ and the V- on the power supply

unit. If nothing, replace the PSU.

Firmware is erased.

Upgrade the firmware.

The screen is

blank.

Firmware is erased.

Upgrade the firmware.

Temp sensor error. Loose connection.

Check the FFC cable connections.

Temp sensor damaged.

Replace the FFC panel.

FFC cable damaged.

Replace the FFC cable.

Pr3Dator panel fault.

Replace the Pr3Dator panel.

Machine is shaking

when homing the

print head.

Loose limit switch connection. Check the connections.
Switch is broken.

Check the limit switch by a multimeter.

Replace the whole cable if faulty.

Read timeout

during firmware

update.

Using old CraftPrint.

Install the latest CraftPrint version.

Firmware need to be erased.

Erase the firmware with the buttons.

Bed does not heat

up.

Loose bed heater connector.

Check the connection.

Broken heating element.

Check the resistance of the heating ele

ment. Replace if infinite.

Hotend

overheating.

Temp sensor is not in place.

Put back the temp sensor into the hotend.

Temp sensor damaged.

Replace the FFC panel.

The printed object

does not stick to

the build plate.

Build plate is dirty.

Clean the build plate with acetone.

The build plate is uneven.

Try to straighten the build plate.

Replace if neccessary.

The build plate is not

calibrated, the nozzle is too

far from the surface.

Calibrate the build plate.

Machine is noisy.

Worn bearings.

Replace the worn bearings.

Worn fans.

Replace the worn fans.

Bad print quality. The nozzle is damaged.

Replace the nozzle.

The nozzle is clogged.

Clean the nozzle. Replace if neccessary.

Filament drive gear dirty.

Clean the filament drive gear.

Filament drive gear worn.

Replace the filament drive gear.

Swing misallignment.

Check the distance between the filament

bearing and the drive gear. Adjust the gap

with the ext_top part, if neccessary.

Hotend damaged.

Replace the hotend.

Содержание CraftBot Plus
























Результаты поиска

Содержание CraftBot Plus

Отзывы:

Похожие инструкции для CraftBot Plus

Бренды по названию

Популярные бренды

CraftUnique CraftBot Plus, Руководство по обслуживанию

Результаты поиска

Содержание CraftBot Plus

Отзывы:

Похожие инструкции для CraftBot Plus

Бренды по названию

Популярные бренды