7
English
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
COMPONENTS (FIG. A)
Intended Use
This jig saw is designed for professional use.
DO nOT
use under wet conditions or in presence of
flammable liquids or gases.
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non-metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
Versatrack
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN Versatrack Trackwall. Hooks and accessories
are sold separately. Please refer to the Versatrack Trackwall
accessory sheet for further information.
Components
Tool
Use
jig saw
professional
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories.
An
accidental start-up can cause injury.
Blade Installation (Fig. B)
1. Push the tool free blade release
6
upward.
2. With teeth facing forward, insert the shank of the saw
blade into the blade holder as far as it will go.
3. Release the lever.
4. Check to ensure blade is secure before cutting.
Fig. B
6
Adjusting the Shoe for Bevel Cuts
(Fig. A, C, D)
WARNING:
Never use the tool when the shoe
is loose
or removed.
The shoe can be set to a left or right bevel angle up to 45°.
1. Turn saw upside down. Use the hex wrench to loosen
the clamping screw
11
and clamp plate
12
.
2. Slide the shoe
8
forward and rotate left or right to the
required angle.
3. Slide the shoe backward so the shoe plate keyways
13
engage the two lock posts on the tool.
4. Tighten clamping screw and clamp plate with its
beveled side towards the tool.
DO nOT
let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
