Craftsman 944.364741 Скачать руководство пользователя страница 15

Страница: 15 / 32

5/8" bolt or pin

Center hole

Blade

GRASS CATCHER

• The grass catcher may be hosed with

water, but must be dry when used.

• Check your grass catcher often for

damage or de te ri o ra tion. Through

normal use it will wear. If catcher needs

replacing, replace only with ap proved

replacement catcher shown in the Re-

pair Parts section of this manual. Give

the lawn mower model number when

ordering.

GEAR CASE

• To keep your drive system work-

ing properly, the gear case and area

around the drive should be kept clean

and free of trash build-up. Clean under

the drive cover twice a season.

• The gear case is filled with lubricant to

the proper level at the factory. The only

time the lubricant needs attention is if

service has been performed on the gear

case.

ENGINE

LUBRICATION

Use only high quality detergent oil rated

with API service classification SJ–SN.

Select the oil's SAE viscosity grade

according to your expected operating

temperature.

Check the crankcase oil level before

starting the engine and after each five (5)

hours of continuous use. Tighten oil plug

securely each time you check the oil level.
TO CHANGE ENGINE OIL

NOTE

: Before tipping lawn mower to

drain oil, empty fuel tank by running en-

gine until fuel tank is empty.

1. Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with plug.

2. Remove engine oil cap; lay aside on a

clean surface.

3. Tip lawn mower on its side as shown

and drain oil into a suitable container.

Rock lawn mower back and forth to re-

move any oil trapped inside of engine.

NOTE:

Although multi-viscosity oils

(5W30, 10W30 etc.) improve starting in

cold weather, these multi-viscosity oils will

result in increased oil consumption when

used above 32°F. Check your engine oil

level more frequently to avoid possible en-

gine damage from running low on oil.

Change the oil after every 25 hours of

operation or at least once a year if the

lawn mower is not used for 25 hours in

one year.

4. Wipe off any spilled oil from lawn

mower or side of engine.

5. Slowly pour oil down the oil fill spout,

stopping every few ounces to check

the oil level with the dipstick.

6. Stop adding oil when you reach the

FULL mark on the dipstick. Wait a

minute to allow oil to settle.

7. Continue adding small amounts of oil,

rechecking the dipstick until oil level

settles at FULL. DO NOT overfill, or

engine will smoke heavily from the

muffler on startup.

8. Always be sure to retighten oil dipstick

before starting engine.

9. Re

con nect spark plug wire to spark

plug.

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20 0 30 40

100

-30

-20 0 20 30

-10

5W-30

SAE 30

Container

Содержание 944.364741

































Результаты поиска

Содержание 944.364741

Отзывы:

Бренды по названию

Популярные бренды

Craftsman 944.364741, Руководство пользователя

Результаты поиска

Содержание 944.364741

Отзывы:

Бренды по названию

Популярные бренды