background image

6

The operation of any lawn 
mower can result in foreign 
objects thrown into the 
eyes, which can result in 
severe eye damage. Always 

wear safety glasses or eye shields while 
operating your lawn mower or performing 
any ad just ments or repairs. We recom-
mend standard safety glasses or a wide 
vision safety mask worn over spectacles.

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED 

The engine speed was set at the factory 
for optimum performance. Speed is not 
adjustable.

ENGINE ZONE CONTROL

 

CAUTION:

  Federal regulations re quire 

an engine control to be installed on this 
lawn mower in order to minimize the 
risk of blade contact injury. Do not un der 
any circumstances attempt to de feat the 
func tion of the operator con trol. The blade 
turns when the engine is running.
•   Your lawn mower is equipped with an 

operator pres ence control bar which 
requires the operator to be positioned 
behind the lawn mower handle to start 
and operate the lawn mower.

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels 
for high cut, adjust cutting height to suit 
your requirements. Me di um position is 
best for most lawns.
•    To change cutting height, squeeze ad-

juster lever to ward wheel. Move wheel 
up or down to suit your re quire ments. Be 
sure all wheels are in the same setting.

NOTE: 

Adjuster is properly positioned 

when plate tab inserts into hole in lever. 
Also, 9-position adjusters (if so equipped) 
allow lever to be positioned between the 
plate tabs.

LOWER WHEELS FOR HIGH CUT

RAISE WHEELS FOR LOW CUT

Plate tab

Lever

TO CONVERT MOWER

Your lawn mower was shipped ready to be 
used as a mulcher.  To convert to bagging 
or discharging:

REAR BAGGING 
•   Lift rear door of the lawn mower and 

place the grass catcher frame hooks 
onto the door pivot pins.

•   To convert to mulching or dis charg ing 

operation, remove grass catch er and 
close rear door.

Pivot pins

Grass 

catcher 

handle

Catcher frame hook

Rear 
door

SIDE DISCHARGING
•   Rear door must be closed.
•   Open mulcher door and install dis-

 charge defl ector under door as shown.

•   Mower is now ready for discharging 

operation.

•   To convert to mulching or bagging opera-

tion, dis charge defl ector must be removed 
and mulcher door must be closed. 

SIMPLE STEPS TO REMEMBER WHEN 
CONVERTING YOUR LAWN MOWER

FOR MULCHING -
1.   Rear door closed.
2.   Mulcher door closed.
FOR REAR BAGGING -
1.   Grass catcher installed.
2.   Mulcher door closed.

FOR SIDE DISCHARGING -
1.   Rear door closed.
2.   Side discharge defl ector installed.

 

CAUTION: 

 Do not run your lawn mower 

with out rear door closed or ap proved 
grass catcher in place.  Never at tempt to 
op er ate the lawn mow er with the rear door 
re moved or propped open.

Open mulcher door

Содержание 944.362631

























Отзывы: