16
SERVICE AND ADJUSTMENTS
WARNING:
To avoid serious injury, before performing any service and adjustments:
1. Release control bar and stop engine.
2. Make sure the blade and all moving parts have completely stopped.
3. Disconnect spark plug wire from spark plug and place wire where it cannot come in
contact with plug.
Handle
bracket
Knob
Bolt
LAWN MOWER
TO ADJUST CUTTING HEIGHT
See “TO ADJUST CUTTING HEIGHT” in
the Operation sec tion of this manual.
REAR DEFLECTOR
The rear defl ector, attached between the rear
wheels of your mower, is provided to minimize
the possibility that objects will be thrown out
of the rear of the mower into the operator
mowing position. If the defl ector becomes
dam aged, it should be replaced.
TO REMOVE DRIVE BELT
1. Remove screws securing rear baffl e.
2. Turn lawn mower on its side with air
fi lter and car bu re tor up.
3. Remove rear baffl e from mower.
4. Remove blade bolt, lockwasher, hard-
ened washer and blade.
5. Remove debris shield.
6. Remove gearcase belt keeper.
7. Remove drive belt.
TO REPLACE DRIVE BELT
1. Place new drive belt on gearcase pul-
ley.
NOTE:
Always use factory approved belt
to assure proper fi t and long life.
2. Reinstall gearcase belt keeper. Be
sure the new drive belt is inside the
tabs of the gearcase belt keeper.
3. Position the blade adapter on the en-
gine crank shaft. Be sure key in adapter
and crankshaft keyway are aligned;
and that the drive belt is inside the tabs
of the belt retainer.
4. Place rear baffl e in mower housing.
5. Reinstall debris shield.
6. Reinstall blade.
7. Return mower to upright po si tion.
8. Reinstall rear baffl e screws.
TO ADJUST HANDLE
Your handle has three (3) height positions
- adjust to a height that suits you.
1. Remove knob and carriage bolt on one
side of the lower handle.
2. While holding handle assembly,
remove knob and car riage bolt from
opposite side, align hole in handle with
desired hole in handle bracket and
reassemble bolt and knob and tighten
securely.
3. Align opposite side of handle with
same positioning hole and secure with
bolt and knob.
Blade
bolt
Hardened washer
Lockwasher
Blade
adapter
Blade
Belt
retainer
Gearcase
belt keeper
Debris
shield
Rear
baffl e
Gearcase
pulley
17
CARBURETOR
Your carburetor is not adjustable. If your
engine does not operate properly due
to suspected carburetor problems, take
your lawn mower to a Sears or other
qualifi ed service center for repair and/or
ad just ment.
IMPORTANT:
Never tamper with the
engine governor, which is factory set for
proper engine speed. Over speed ing
the engine above the factory high speed
setting can be dangerous. If you think
the engine-governed high speed needs
adjusting, contact a Sears or other
qualifi ed service center, which has proper
equip ment and ex pe ri ence to make any
nec es sary adjustments.
ENGINE
Maintenance, re pair, or re place ment of
the emission con trol de vic es and sys tems,
which are be ing done at the cus tom ers ex-
pense, may be performed by any non-road
engine repair es tab lish ment or individual.
Warranty repairs must be performed by an
authorized engine man u fac tur er's service
outlet.
ENGINE SPEED
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to a
Sears or other qualifi ed service center for
repair and ad just ment.
STORAGE
Immediately prepare your lawn mower for storage at the end of the season or if the unit
will not be used for 30 days or more.
FOLD
FORWARD
FOR
STORAGE
MOWING
POSITION
Lower handle
Operator
presence
control bar
Upper
handle
Handle
knob
Handle
bracket
Knob
Bolt
LAWN MOWER
When lawn mower is to be stored for a
period of time, clean it thor oughly, remove
all dirt, grease, leaves, etc. Store in a
clean, dry area.
1. Clean entire lawn mower (See
“CLEANING” in the Maintenance sec-
tion of this manual).
2. Lubricate as shown in the Main te nance
section of this manual.
3. Be sure that all nuts, bolts, screws, and
pins are securely fas tened. Inspect
moving parts for damage, breakage
and wear. Replace if necessary.
4. Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your han dle for storage.
1. Loosen the two (2) handle knobs on
sides of the upper handle and allow
handle to fold down to the rear.
2. Remove the two (2) handle knobs and
carriage bolts on sides of the lower handle
and pivot entire handle as sem bly forward
and allow it to rest on mower.
3. Reinstall knobs and carriage bolts to
lower handle / handle brackets for safe
keeping.
• When setting up your handle from
the storage position, lower han dle will
require manually locking into mowing
position.
IMPORTANT:
When folding the handle
for storage or transportation, be sure to
fold the handle as shown or you may dam-
age the control cables.
