10 - English
OPERATION
LCD DISPLAY
See Figures 6 - 7, pages ii and iii.
When the radio/charger is connected to a power supply
and in the ON position, the LCD display will show the
time, frequency, mode, and settings.
NOTE: The illustrations of the LCD display shown in this
manual are only examples of the frequencies you may see
on your radio/charger and are not the exact frequencies
that you may choose to listen to.
MENU NAVIGATION BUTTONS
See Figures 6 - 7, pages ii and iii.
Use the menu navigation buttons to turn the radio/charger
on and off, control the volume, change frequencies, toggle
between modes and set the time.
TURNING THE RADIO/CHARGER ON AND OFF:
Press the
ON/OFF button to turn the radio/charger ON
and OFF.
When the radio/charger is on and a battery pack is
connected as the power supply, the [
] symbol will be
shown in the LCD display. If the battery charge is low, a
flashing low battery indicator will be displayed [
]. If
the radio is connected to an AC power supply, the battery
indicator will disappear.
ADJUSTING THE VOLUME:
When the radio/charger is turned ON, the unit will return
to the last volume setting used.
To increase the volume, press the
VOL + button.
To decrease the volume, press the
VOL - button.
SWITCHING MODES:
To switch modes, press the
MODE button. The selected
mode will be displayed above the frequency. Press the
MODE button until the desired mode is selected. There
are four modes:
FM mode
AM mode
AUX mode
BLUETOOTH
®
mode
AM/FM TUNING:
Use the
SCAN and SCAN buttons to manually tune
to the desired radio frequency. The selected frequency is
displayed on the LCD.
Press the
SCAN button to tune to a lower frequency
and press the
SCAN button to tune to a higher
frequency.
NOTE: Briefly press either button (not press and hold)
to tune one frequency step at a time. Press and hold
either button to quickly find the next frequency with
clear reception.
To decrease interference or electrical noise, adjust the
position of the antenna or move the radio/charger to a
higher elevation. The antenna folds into the handle and
out of the way when not in use.
STORING A PRESET IN MEMORY:
The memory feature saves up to 20 frequencies as
presets in the radio’s memory. You can save up to ten (10)
frequencies each for FM and AM modes.
Tune to the desired AM or FM frequency.
Press and hold the
PRESET button until the word
“MEMORY” and the preset position number flash on
the screen.
Press the
SCAN or SCAN button to choose a
preset position number.
NOTE: There are ten (10) preset positions for FM and
ten (10) for AM. Only one station can be saved in each
preset position.
Press the
PRESET button again to store the frequency.
To tune to presets (FM or AM mode):
Press and release the
PRESET button to cycle through
each preset position number and its associated
frequency.
SETTING THE CLOCK:
The time appears on the LCD display when the radio/
charger is on.
Press and hold the
CLK/DSPY button until the “hour”
display blinks.
Press the
VOL + or VOL - button to select the hour.
NOTE: Time is displayed in 12-hour format only. To
select an hour that is after noon and before midnight,
cycle the hours until “PM” appears in the display.
Press and release the
CLK/DSPY button to lock in the
hour setting. “Minutes” will begin to blink.
Press the
VOL + or VOL - button to select the desired
number.
Press and release the
CLK/DSPY button again to
confirm the time.
USING A PHONE/MP3 PLAYER (NOT
INCLUDED) WITH THE RADIO/CHARGER
See Figure 8, page iii.
Press the
MODE button until AUX mode is highlighted.
Connect one end of a 3.5 mm audio patch cord
(maximum 8 in. long) to the device.
Connect the other end of the 3.5 mm patch cord to the
auxiliary input jack.
The phone/MP3 player must be on and in play mode
for sound to be heard through the speakers.