background image

3. Installation Preparation.

4. Hanging Bracket Installation.

page 4

ON

OFF

ON

OFF

Turn off circuit breakers to current fixture from breaker 
panel and be sure operating light switch is turned to the 
OFF position. 

WARNING: 

Failure to disconnect power supply prior to 

installation may result in serious injury.

Remove existing fixture. 

WARNING:

 When using an existing outlet box, be sure the 

outlet box is securely attached to the building structure and 
can support the full weight of the fan. Ensure outlet box is 
clearly marked "Suitable for Fan Support." If not, it must be 
replaced with an approved outlet box. Failure to do so can 
result in serious injury.

CAUTION

Be sure outlet box is grounded properly and that a 

ground wire (

GREEN

 or bare) is present.

Install hanging bracket to outlet box using original screws, 
spring washers and flat washers  provided with new or 
original outlet box.

*

 If installing on a vaulted ceiling, face 

opening of hanging bracket towards high point of ceiling. 
Arrange electrical wiring around the back of the hanging 
bracket and away from the hanging bracket opening.

*Note

: It is very important that you use the proper hardware 

when installing the hanging bracket as this will support the 
fan. 

hanging bracket

spring washers

outlet box screws

flat washers

Installation requires these tools:

Phillips screwdriver, flathead screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

downrod

installation

flushmount

installation

To prevent personal injury and damage, ensure 
that the hanging location allows the blades a 
clearance of 7 feet (2.13m) from the floor and 
30in. (76cm) from any wall or obstruction. 
This fan is suitable for room sizes up to 
400 square feet (37.2 square meters).

This fan can be mounted with a 

downrod

on a regular (no-slope) or vaulted ceiling. The 
hanging length can be extended by purchasing a 
longer downrod (0.5in. /1.27cm diameter). Other 
installation, such as 

flushmount

, is 

NOT

 available 

for this fan.

Vaulted ceiling 
angle is not to 
exceed 25 degrees.  

12f

t.

 - 20f

t.

12ft. - 20ft.

(3.66m - 6.1m)

(3.66m - 6.1m)

blade edge

7 feet

(2.13m)

(76cm)

30 

inches

Содержание Retreat RET52












Отзывы: