background image

 

7

OILING THE NAILER 

 

The CX901 Brad Nailer needs to be 
lubricated before every use. Place three to 
four drops of pneumatic tool oil (provided) 
in the nailer air inlet every two hours of 
continuous use. See figure-2. 

Figure-2 Lubricating the nailer 

 
 

LOADING THE NAILER 

 

Disconnect the nailer form the air supply. 
 
The CX901 accepts nails with the following 
specifications: 
 
Gauge: 18 
Length: 5/8" (15mm) to 2" (50mm) 
Capacity: 100 pieces 
 
Depress and hold the magazine lock lock 
while pulling the magazine cover back all 
the way. 
 
Slide a strip of nails, pointed-end down into 
the magazine. 
 
Push the magazine cover forward until it is 
locked in its place. 
 
 
 
 

OPERATING THE NAILER 

 

Before operating the nailer, make sure you 
have read and understood the instructions 
given in this manual. 

 
Always use the nailer first on a piece of 
scrap wood; thick enough for the length of 
the nails, loaded in the magazine, before 
using it on the actual work-piece. 
 
 
To operate the nailer: 
 
Connect the air supply hose to the nailer. 
 
Check the work-piece and make sure it is 
free of knots, metals, or any other foreign 
objects that will cause deflection.  
 
Hold the nailer perpendicular to the surface 
of the work-piece. Depress the safety nose 
mechanism against the wood and make 
sure your other hand and body parts are 
positioned out of the way of the potential of 
the nail in case of deflection. 
 
Pull the trigger and drive the nail into the 
work-piece. Remove the nailer and check 
the nail for proper depth. 
 
If the nail is shot too deep into the wood, 
slightly decrease the air pressure. 
 
If the depth is too shallow, slightly increase 
the air pressure. 
 
 

WARNING! 

Lubricate the nailer with a few drops of 
oil as instructed in the manual, before 
operating it. Failure to do so could result 
in internal damage to the nailer and will 
void the warranty. 

Содержание CX901













Отзывы: