background image

 

23

Tilting the Table Backward 

 
To tilt the table backward, you will need to 
loosen the bolts shown in figure-35 and 
adjust them as needed using a wrench. 

 

Figure-35 Bolts to tilt the table backward 

 
 

 

Table & Base 

 

The moisture from the wood dust remains 
on the table surface and can cause rust. 
Protect the un-painted cast iron surfaces of 
the table by cleaning the table after every 
use or apply a protective coating. 
 
If the table becomes harder to tilt, remove 
the table and apply a few drops of oil on the 
trunnions. 

 
 
V-Belts 

 

The V-belts stretch with use, and should be 
re-tensioned periodically. To ensure 
optimum power transfer from the motor to 
the blade, the belt must be in good 
condition and under proper tension.  
 
Check the V-belts at least after every 3 
months and more often if the band saw is 
used daily. 

To Inspect the V-Belts 

 

1. 

Turn the power switch off and 
disconnect the cord from the power 
source. 

 

2. 

Lift the blade tension handle up and 
release the tension. 

 

3. 

Open the lower and upper cabinet and 
remove the blade. (See page-21 
Removing/Changing the Blade) 

 

4. 

Remove the lower wheel by removing 
the hex bolt securing the wheel to the 
saw body.  See figure-36 

 

5. 

Once the wheel is removed, you will 
have access to the V-belts. Check if the 
V-belts are in good condition and 
properly tensioned. 

 

Figure-36 Lower wheel and pulleys 

Содержание CX101

































Отзывы: