The Security
✚
®
remote control (with blue push buttons) works
only with rolling code door openers and light controls (with an
orange SRT button and yellow indicator light). The code
between the remote control and the receiver changes with
each use, randomly accessing over 100 billion new codes.
Instructions are given below for programming your opener to
match the remote control's code. The additional remote
control buttons can also activate other Security
✚
®
garage
door openers and/or light controls. (Instructions for
programming light products are included with those
accessories.)
®
Owner’s Manual for SECURITY
✚
®
Models
139.18790B - Single-Function Remote Control
139.18791B – 3-Function Remote Control
139.18792 & 139.18799 – Compact 3-Function
Remote Control
Select a remote control push
button to operate opener
COMPACT
3-FUNCTION
REMOTE CONTROL
3-FUNCTION
REMOTE CONTROL
SINGLE-FUNCTION
REMOTE CONTROL
The Remote Control Batteries
The lithium batteries should produce
power for up to 5 years. To replace
batteries, use the visor clip or
screwdriver blade to pry open the case,
as shown. (“Open” location is stamped
on back of transmitter case.) Insert
battery matching polarity instructions
inside the remote cover or on the printed
circuit board.
Replace cover as follows:
Single and 3-
Function remote:
Insert the 3 tabs at the opposite end and snap
shut.
Compact 3-Function remote:
Snap shut along both sides.
Dispose of old batteries properly.
3-FUNCTION
COMPACT
Twist here
to open
Open this end
first to avoid
cracking
housing
Replacement Parts:
Remote control housing only (no circuit board) for:
Single-Function . . . . . . . . . . . . . . . . . . . . . . . . . . 41A 5076-1
3-Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41A5032
Compact 3-Function (139.18792) . . . . . . . . . . . . . . 41A5062
Compact 3-Function (139.18799) . . . . . . . . . . . . . 41A5078-8
Visor Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29B134
3V 2032 Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . 10A20
(1 required for Remote Models 139.18790B, 139.18791B,
139.18792, 139.18799)
3V 2016 Lithium Battery . . . . . . . . . . . . . . . . . . . . . . . . . 10A19
(2 required for Remote Models 139.18790, 139.18791)
© 2006, Sears Canada, Inc.
114A2151D
All Rights Reserved
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
WARNING
CAUTION
WARNING
WARNING
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
WARNING
CAUTION
WARNING
WARNING
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
1. Press and release the “learn” button on the
motor unit. The learn indicator light will glow
steadily for 30 seconds.
2. Within 30 seconds, press and hold the selected
push button on the hand-held remote.
3. Release the button when the motor unit light
blinks. It has learned the code. If light bulbs are
not installed, two clicks will be heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor unit
until the learn indicator light goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote or keyless
entry you wish to use.
Instructions are Described and Illustrated Below
