CR Remeha Quinta Pro 115 Скачать руководство пользователя страница 29

Страница: 29 / 92

CAUTION

The following boiler components are at a voltage of

230V:

Electrical connection of the heating pump (Central

heating).

Electrical connection of the combined gas valve unit.

Electrical connection of the fan.

The majority of components in the control panel.

Ignition transformer.

Connection of the power supply cable.

CAUTION

When the power supply cable has to be replaced, it

must be ordered from

Remeha

The boiler plug must be accessible at all times.

It is possible to connect various control, safety and regulation systems

to the boiler. The standard control PCB can be extended with:

For the optional PCBs, see chapter: "Optional electrical

connections", page 34

4.8.2.

Recommendations

WARNING

Only qualified professionnals may carry out electrical

connections, always with the power off.

The boiler is entirely pre-wired. Do not modify the

connections inside the control panel.

Earth the appliance before making any electrical

connections.

Make the electrical connections of the boiler according to:

The instructions of the prevailing standards.

The instructions on the electrical diagrams provided with the

boiler.

The recommendations in the instructions.

CAUTION

Separate the sensor cables from the 230 V cables.

Quinta Pro 30 - 45 - 65 - 90 - 115

4. Installation

250413 - 123157-03

Содержание Quinta Pro 115





























































































Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды

CR Remeha Quinta Pro 115, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Quinta Pro 115

Отзывы:

Похожие инструкции для Quinta Pro 115

Бренды по названию

Популярные бренды