background image

Talos

TM

 T700 Install Guide 

The Talos bill validator is designed to fit into the standard bill acceptor opening 
in most vending machines and can be mounted on existing studs or a mounting 
bracket. 

 

Features

 

Four way bill acceptance

 

Coupon and bill configuration

 

Supports High Visibility and Credit Card Reader Bezels

 

Interface 

The Talos bill validator operates via MDB interface. The 24VDC MDB harness is 
included.

 

Operating Voltage 

See the label on the side of the device. 

Installation

Before installation, remove the Talos bill validator from the packaging and inspect for any physical damage. If damaged, contact customer service at 1-800-345-8215.

1.  Turn off power to the vending machine.
2.  Mount the Talos bill validator on the mounting studs, through the opening in the front of the vendor and secure using the included hardware. 
3.  Connect the Talos bill validator to the MDB harness. Apply gentle pressure to connect; the pins will bend if forced. 
4.  Turn on power to the vending machine. 
5.  Check the LEDs on the front of Talos. The LEDs should be flashing. In some cases, the machine door must be closed first.
6.  Once the LEDs are flashing, test the validator with a $1 bill. 

 

    a. Insert $1 and confirm that it stacks and credit is given. 

 

    b. Repeat this process for any other enabled bills. 

7.  When your test is complete, remove the test bills from the bill magazine. 

The installation is now complete. Refer to the other sections of this guide to configure the device, if necessary. 

Enabling Bills and Vend Coupons

Follow this process to enable or disable bills or vend coupons:

1.  Remove the bill magazine, then use a pencil or a screwdriver to press the button to enter configuration mode:
2.  Reattach the bill magazine. 
3.  Insert the bill or vend coupon. 
4.  The bezel LEDs flash when the bill or vend coupon is returned. 
5.  Count the flashes to determine the outcome using the chart on the next section.

Press this button

Talos Install Guide_Web_5.24.19.indd   1

5/24/2019   9:57:14 AM

Содержание Talos T700

Страница 1: ...arness Apply gentle pressure to connect the pins will bend if forced 4 Turn on power to the vending machine 5 Check the LEDs on the front of Talos The LEDs should be flashing In some cases the machine door must be closed first 6 Once the LEDs are flashing test the validator with a 1 bill a Insert 1 and confirm that it stacks and credit is given b Repeat this process for any other enabled bills 7 W...

Страница 2: ... Face up or down in either direction 2 Bills Enabled On or off to enable or disable a bill 3 Recycled Bill Can be left blank but is required for the recycler 4 Accept Inhibit Requires a Recycler 5 Acceptance Mode Mode 0 Factory default No acceptance modes active Mode 1 If fraud is detected the validator enters an out of service time out the stacker plate extends into the bill magazine and the beze...

Страница 3: ...hold a bill in the bill path until the bezel lights flash Count the flashes and refer to the chart below Flashes Problem Solution None No power Restore power to validator or machine 1 or 4 Bill path blocked Check for jams Remove bill magazine and lower housing assembly and inspect 2 Another vending component Ensure the unit has been enabled then check Vending Machine Controller Coin manager and co...

Страница 4: ...ions at any time While every effort has been made to ensure that the information in this publication is accurate CPI disclaims any liability for any direct or indirect losses howsoever caused arising out of use or reliance on this information This document does not necessarily imply product availability Note Your product may differ slightly from some of the illustrations in this document If this h...

Отзывы:

Похожие инструкции для Talos T700