Cozzia CZ-388 страница 9 Скачать руководство пользователя

Страница: 9 / 49

No Rolling.

①

Terminal or Wire Poorly Contacts.

②

Down-stroke Photo-electricity

Subassembly Fails.

③

Up-stroke Photo-electricity

Subassembly Fails.

④

Rolling Motor Fails.

⑤

Main PCB Fails.

①

Plug the terminal securely or

replace the wires.

②

Replace Down-Stroke Sub-

assembly.

③

Replace Up-Stroke Sub-

assembly.

④

Replace Rolling Motor.

⑤

Replace main PCB.

No kneading.

①

The terminals on main PCB and wires are

poorly connected.

②

Kneading motor fails.

③

Main PCB fails.

①

Plug the terminal securely or

replace the wires.

②

Replace the kneading motor.

③

Replace main PCB.

No tapping.

①

The terminals on main PCB and wires are

poorly connected.

②

Tapping motor fails.

③

Main PCB fails.

①

Plug the terminal securely.

②

Replace the tapping motor.

③

Replace main PCB.

No response

when pressing

the keys on the

remote

controller.

①

The terminals and wires are poorly

connected.

②

The PCB in the remote controller fails.

①

Plug the terminal securely or

replace the wires.

②

Replace the remote controller.

Back rest

cannot be

reclined or

raised

①

The terminals of reclining actuator and

wires are poorly connected.

②

The reclining actuator fails.

③

Main PCB fails.

①

Plug the terminal securely.

②

Replace reclining actuator.

③

Replace main PCB.

Foot rest

cannot be

raised or

lowered.

①

The terminals of foot rest actuator and

wires are poorly connected.

②

The foot rest actuator fails.

③

Main PCB fails.

①

Plug the terminal securely.

②

Replace foot rest actuator.

③

Replace main PCB.

No vibration by

the motors in

the seat-pad.

①

Print motors fail.

②

The terminals and wires are poorly

connected or the wires fail.

③

Main PCB fails.

①

Replace the print motor.

②

Plug the terminal securely or

replace the wires.

③

Replace main PCB.

Содержание CZ-388


















































Результаты поиска

Содержание CZ-388

Отзывы:

Похожие инструкции для CZ-388

Бренды по названию

Популярные бренды

Cozzia CZ-388, Руководство по техническому обслуживанию

Результаты поиска

Содержание CZ-388

Отзывы:

Похожие инструкции для CZ-388

Бренды по названию

Популярные бренды