COZY BBT103 and Скачать руководство пользователя страница 17

Page 17

SIDE VALVE CONCEALER KIT - SVCK5/10

NOTE:  This kit has been designed and certified for use with a Cozy gas baseboard heater only.  Use only factory
supplied kit and components.

STEP 1.

With the offset up and out from the wall, place the mounting bracket flush to the right side of the
heater cabinet.  Align the top of the mounting plate with the top of heater cabinet.  Mark the
location of the mounting holes.  See Figure 1.

STEP 2.

Drill holes where marked.  Depending on wall material, install wall anchors (nor provided) if
needed.

STEP 3.

Secure mounting plate to wall with screws (not provided).

STEP 4.

Attach the cover to the mounting plate by placing the cover top edge over the offset on the
mounting plate.  Push the cover in toward wall until catch snaps into place.  See Figure 2.

STEP 5.

For access to the manual gas shut off valve, locate finger handle at the bottom of the cover.  Pull
out until snap catch releases then lift cover up to remove from mounting plate.  See Figure 2.

FIGURE 1

Offset must be out

from wall

Mounting

Holes (4)

Mounting

Plate

Manual gas shut

off valve

COZY Gas

Baseboard

Heater

FIGURE 2

Manual gas

shut off valve

Cover

Cabinet

catch

Finger

handle

COZY Gas
Baseboard

Heater

Содержание BBT103 and



























Отзывы: