COX Stockman 4000 A16314E, Руководство владельца/оператора

Страница: 4 / 50

19 March 2015
Page 4
OWNERS MANUAL FOR MODEL A16314E rev 1
INTRODUCTION:
The purpose of this procedure is to ensure the dealer/
distributor has assembled & made the necessary checks, &
adjustments, before the mower is operational, and
instructed the owner in its safe operation & maintenance.
This procedure begins upon receiving the crated mower and
is finalised once the mower has been either sold or leaves
the dealer/distributors premises. This is the minimum
amount of work required, however it should not be limited
to only the areas detailed in this procedure.
RESPONSIBILITY:
It is the responsibility of the dealer/distributors to ensure
that before a mower is delivered to a customer, it is in
perfect operational condition.
PROCEDURE:
CHECK SHIPPING CRATE & CONTENTS FOR DAMAGE
UNCRATE THE MOWER
CHECK COMPONENTS SUPPLIED IN SEAT
PROTECTION BAG
Engine owners Manual 1
Owner/Operator Manual 1
Tube Spanner (AM006C1) 1
Tommy Bar (AM007) 1
Ignition Keys (AM015) 2
Spark plug tube Spanner
(AM295 B&S or AM005G0 16HP Honda) 1
Steering Wheel (SW13) 1
Roll Pin (DP10) 1
Drive cone clearance Gauges (13126) 2
Seat Springs (A163060) 2
Screws M 8X 20 2
Seat spring Washers 5/16” 2
Nuts M 8 Nyloc 2
Warranty Card 1
Pre-delivery instruction Sheet 1
REMOVE SEAT PROTECTION BAG
Remove the four screws, lock washers and plain washers
securing the seat to the seat mount & remove the plastic
bag from the seat. Install the four screws, spring washers,
and plain washers, through the slots in the seat mount and
adjusted the seat to the desired position using the slots
provided, & tighten screws.
ASSEMBLE STEERING WHEEL TO MOWER
(see page 5 for exploded view)
Roll Pin Type—
To attach the steering wheel, align the hole in the steering
wheel boss to the hole in the steering shaft and use a
hammer and suitable punch to drive the DP10 roll pin in,
through the hole in the steering shaft cover into the steering
wheel and shaft. Ensure that the pin is situated centrally in
the steering wheel boss and that the steering is free to turn.
Press the steering wheel center cover into place using hand
pressure only.
ASSEMBLE SEAT MOUNT & SEAT SPRINGS TO
MOWER
(see page 5 for exploded view)
Install the two seat springs using the screws, washers, nuts,
to the transmission cover, and tighten the screws, washers,
and nuts.
Install the Seat & Mounting to the Transmission Housing
using the Screws and Nuts.
CHECK TYRE PRESSURE
Before operation ensure that all tyre pressures are equal.
The recommended pressure is 140 kpa (20 P.S.I.).
CHECK ENGINE OIL
Before operation ensure that engine oil level is to the full
mark on the dipstick. (Refer engine owners manual for
procedure & if some oil needs to be added refer Engine
owners Manual for Correct Grade).
CHECK FUEL
Ensure the fuel tap at the bottom left side of fuel tank is
turned to the on position before attempting to start engine.
(Use unleaded fuel only).
Turn off fuel tap after use.
CHECK CLUTCH PLATE ADJUSTMENT
Engage and disengage the cutter disengage lever a few
times and leave in the engaged position, this will centre the
clutch arm assembly in the neutral position. Loosen the four
square head set screws on the clutch plates using tube
spanner (AM006C1) and tommy bar (AM007). Insert the
clearance gauges supplied, one between the forward clutch
plate and cone and the other between the reverse clutch
plate and cone and hook them onto the intershaft. Slide
both clutch plates against the clearance gauges and drive
cone, tighten the set screws firmly onto the flat on the
intershaft. Remove gauges.
CHECK SAFETY SWITCH OPERATION
Foot Switch
- With cutter disengage lever in disengaged
position, attempt to start the engine without depressing the
foot switch. Engine should not start.
Disengagement Switch - While sitting on seat with foot
on foot switch and cutter lever in engaged position, attempt
to start the engine. Engine should not start.
Start Switch
With Cutter Lever in disengaged position & foot switch
depressed start engine.
Seat Switch - While sitting on seat with engine running
engage cutter and lift weight from seat. Engine should cut
out.
CHECK CUTTER BELT DISENGAGEMENT
Ensure that when the cutter belt is in the disengaged
position that the belt does not overlap when squeezed
together, if this occurs adjust the cutter engage lever until
correct disengagement is achieved.
A16314E PRE-DELIVERY INSTRUCTIONS
Assemble Seat Mount &Seat Springs to Mower
Remove the words: - (brackets to the top rear of the trans mission housing,).
And replace with: - (transmission cover,)
Add the words: - (, Washers,) between the words Screws and