background image

2

Hazard Signal Word Definitions

This is the safety alert symbol. It is used to 

alert you to potential personal injury hazards. 

Obey all safety messages that follow this 

symbol to avoid possible injury or death.
DANGER (red) indicates an imminently 
hazardous situation which, if not avoided, will 
result in death or serious injury.
WARNING (orange) indicates a potentially 
hazardous situation which, if not avoided, 
could result in death or serious injury.
CAUTION (yellow) indicates a potentially 
hazardous situation which, if not avoided, 
may result in minor or moderate injury.
CAUTION (yellow) used without the safety

alert symbol indicates a potentially

hazardous situation which, if not avoided,

may result in property damage.

DANGER

WARNING

CAUTION

CAUTION

Engine is shipped without oil.

- Before starting engine, fill with SAE 10W-30 motor oil.
- See engine manual for engine oil capacity.

Hydraulic Oil Tankis shipped withoutoil.

- When adding oil, verify oil level is 1 level from top of hydraulic reservoir       
  (not including fill neck).

Closely inspect all log splitter components.

- If you have damaged components then: Contact the freight company 
thatdelivered the unit and file a claim.

Содержание l2T



















Отзывы: