COX a123, Руководство по эксплуатации для владельца

Страница: 5 / 56

31 May 2013
Page 5
OWNERS MANUAL FOR MODELS A15713A & A15813A
PRE-DELIVERY INSTRUCTIONS
INTRODUCTION:
The purpose of this procedure is to ensure the dealer/distributor has
assembled & made the necessary checks, & adjustments, before the
mower is operational, and instructed the owner in its safe operation &
maintenance. This procedure begins upon receiving the crated mower
and is finalised once the mower has been either sold or leaves the
dealer/distributors premises. This is the minimum amount of work
required, however it should not be limited to only the areas detailed in
this procedure.
RESPONSIBILITY:
It is the responsibility of the dealer/distributors to ensure that before
a mower is delivered to a customer, it is in perfect operational
condition.
PROCEDURE:
CHECK SHIPPING CRATE & CONTENTS FOR DAMAGE
UNCRATE THE MOWER
CHECK COMPONENTS SUPPLIED IN SEAT PROTECTION BAG
Engine owners Manual 1
Owner/Operator Manual 1
Tube Spanner (AM006C1) 1
Tommy Bar (AM007) 1
Ignition Keys (AM015) 2
Spark plug tube Spanner
(AM295 B&S or AM005G0 16HP Honda) 1
Spark plug Spanner 13HP Honda
Steering Wheel (SW13) 1
Roll Pin (DP10) 1
Drive cone clearance Gauges (13126) 2
Seat Springs (13060) 2
Screws M 8X 20 2
Seat spring Washers 5/16” 2
Nuts M 8 Nyloc 2
Warranty Card 1
Pre-delivery instruction Sheet 1
REMOVE SEAT PROTECTION BAG
Remove the four screws, lock washers and plain washers securing the
seat to the seat mount & remove the plastic bag from the seat. Install
the four screws, spring washers, and plain washers, through the slots
in the seat mount and adjusted the seat to the desired position using
the slots provided, & tighten screws.
ASSEMBLE STEERING WHEEL TO MOWER
Roll Pin Type— To attach the steering wheel, align the hole in the
steering wheel boss to the hole in the steering shaft and use a
hammer and suitable punch to drive the DP10 roll pin in, through the
hole in the steering shaft cover into the steering wheel and shaft.
Ensure that the pin is situated centrally in the steering wheel boss and
that the steering is free to turn.
Keyed Type— Remove tape attaching woodruff key to steering shaft.
Remove the screw & washers attached to the steering shaft.
Lubricate taper on steering shaft with grease or anti-seize. Place
steering wheel with keyway aligned with woodruff key on shaft.
Assemble the screw and washers onto the shaft with 1/2”a/f socket,
extension & wrench & tighten to 23Nm.
Press the steering wheel center cover into place using hand pressure
only.
ASSEMBLE SEAT MOUNT & SEAT SPRINGS TO MOWER
Install the two seat springs using the screws, washers, nuts, to the
brackets at the top rear of the Transmission Housing, and tighten the
screws, and nuts.
Install the Seat & Mounting to the Transmission Housing using the
Screws and Nuts.
CHECK TYRE PRESSURE
Before operation ensure that all tyre pressures are equal.
The recommended pressure is 140 kpa (20 P.S.I.).
CHECK ENGINE OIL
Before operation ensure that engine oil level is to the full mark on the
dipstick. (Refer engine owners manual for procedure & if some oil
needs to be added refer Engine owners Manual for Correct Grade).
CHECK FUEL
Ensure the fuel tap at the bottom left side of fuel tank is turned to the
on position before attempting to start engine. (Use unleaded fuel
only).
Turn off fuel tap after use.
CHECK CLUTCH PLATE ADJUSTMENT
Engage and disengage the cutter disengage lever a few times and
leave in the engaged position, this will centre the clutch arm assembly
in the neutral position. Loosen the four square head set screws on
the clutch plates using tube spanner (AM006C1) and tommy bar
(AM007). Insert the clearance gauges supplied, one between the
forward clutch plate and cone and the other between the reverse
clutch plate and cone and hook them onto the intershaft. Slide both
clutch plates against the clearance gauges and drive cone, tighten the
set screws firmly onto the flat on the intershaft. Remove gauges.
CHECK SAFETY SWITCH OPERATION
Foot Switch - With cutter disengage lever in disengaged position,
attempt to start the engine without depressing the foot switch. Engine
should not start.
Disengagement Switch - While sitting on seat with foot on foot
switch and cutter lever in engaged position, attempt to start the
engine. Engine should not start.
Start Switch
With Cutter Lever in disengaged position & foot switch depressed start
engine.
Seat Switch - While sitting on seat with engine running engage
cutter and lift weight from seat. Engine should cut out.
CHECK CUTTER BELT DISENGAGEMENT
Ensure that when the cutter belt is in the disengaged position that the
belt does not overlap when squeezed together, if this occurs adjust
the cutter engage lever until correct disengagement is achieved.
Bonnet shown in closed
position underneath dash
panel extension before
attaching bonnet strap.
Roll Pin type steering wheel