manualshive.com logo in svg

Covidien Newport e360, Руководство по обслуживанию

Поделиться
Скачать
Covidien Newport e360 Скачать руководство пользователя страница 65

Front Panel Assembly

 Service Manual

 4-5

To remove and reinstall the top cover, refer to 

Figure 4-2.  

and perform the following steps:

1.

Rotate the ventilator so the rear of the ventilator is facing you.

2.

Locate the six screws (three on each side) securing the cover to the ventilator and remove.

3.

Grab the handles on the sides of the ventilator, pull the sides away from the chassis, and slide the cover 
off of the ventilator.

4.

Reinstall the top cover by reversing steps 2 and 3.

4.7

Front Panel Assembly

Figure 4-3.  

Front Panel Assembly

To remove and reinstall the front panel assembly, refer to 

Figure 4-3.  

and perform the following 

steps:

1.

Remove the top cover by following the procedure in section 

4.6

, “

Top Cover (CVR2101M)

.” 

2.

Locate the four screws (two on each side) securing the front panel assembly to the chassis of the 
ventilator and remove.

3.

Carefully pull the front panel assembly forward and away from the ventilator chassis. 

1

Screws (two of four securing front panel assembly to chassis)

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды