manualshive.com logo in svg

Covidien Newport e360, Руководство по обслуживанию

Поделиться
Скачать
Covidien Newport e360 Скачать руководство пользователя страница 38

Maintenance, Overhaul, and Software Upgrade

2-14 

 Service Manual

2.7.8

Inhalation Outlet Check Valve

Figure 2-11.  

Inhalation Outlet Check Valve

To replace the inhalation outlet check valve, refer to 

Figure 2-11.  

and perform the following steps: 

1.

Remove the mixing block by removing the two retaining screws (see 

Figure 2-13.  

).

2.

Remove the inhalation adapter from the inhalation outlet assembly (see 

Figure 2-5.  

).

3.

Using your finger, push out the inhalation outlet check valve (see 

Figure 2-11.  

).

4.

Replace the inhalation outlet check valve diaphragm (VLV2100M).

5.

Reinstall the components and assembly by reversing steps 1-3.

2.8

Overhaul Procedures

WARNING:
Disconnect electrical power, air and oxygen sources before attempting any disassembly.

2.8.1

Inlet Water Trap Filter and O-Ring Assembly

To replace the inlet filter and o-ring assemblies, follow the procedure in section 

2.7.1

, “

Inlet Water 

Trap Filters and O-Ring Assembly

.”

1

Inhalation outlet check valve

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды