background image

 

 

Instruction Manual 

CU560-2

FM Portable Radio 

 

Thank you for purchasing a 

COVALUE

 two-way radio. This simple to use radio adopts the latest 

advances in technology, providing reliable communication in today’s demanding communication 

environment.  

 

Notice to the User: 

·

  Please read this instruction manual before operating this radio.   

·

  It’s prohibited to use the radio or charge it at any area with a potentially explosive atmosphere 

(where the air contains gas, dust and smog, etc.), as well as while taking on fuel, or while 

parking at a gasoline service station; or any area where radio communication is prohibited 

(such as a hospital or a airport.) 

·

  It’s prohibited to operate the radio without permission in areas where the government laws 

prohibit radio communication. 

·

  Please don't expose the radio to direct sunlight for a long time; don't place the radio near any 

heating devices, either. 

·

  Please don't put the radio in extremely dusty, moist humid areas or unstable surfaces. 

·

  Only qualified personal, with proper tools and instruments are allowed to service and repair the 

radios, do not disassemble the radio by yourself to avoid damages. 

 

 

 

 

 

FCC & IC Warning: 

Operation is subject to the following two conditions: 
(1) this device may not cause interference, and (2) this device must   
accept any interference,including interference that may cause undesired   
operation of the device. 
Any Changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the equipment.     

FCC Radiation Exposure Statement:     

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment.   
This transmitter must not be co-located or operating in conjunction with any other 
antenna or transmitter.   

Under Industry Canada regulations, this radio transmitter may only   
operate using an antenna of a type and maximum (or lesser) gain 
approved for the transmitter by Industry Canada. To reduce potential   
radio interference to other users, the antenna type and its gain should   
be so chosen that , the equivalent isotropically radiated power (e.i.r.p.) 
is not more than that necessary for successful communication. 

Содержание CU560-2
























Отзывы: