manualshive.com logo in svg

Country Hearth 2000, Руководство владельца по эксплуатации и инструкции

Поделиться
Скачать
Country Hearth 2000 Скачать руководство пользователя страница 5

Ussc 

5

Tools and Materials Needed For Installation

You will need a drill with a 1/8” bit to install sheet metal screws into connector pipe. A 5/16” socket/wrench or screw driver 

to install pedestal trim, room air deflector, and blower assembly described below. A 1/2” socket/wrench to install flue 

collar. A non-combustible floor protector as specified in this manual. All chimney and chimney connector components 

required for your particular chimney installation. For mobile homes, see page 13.

Assembly

Flue Collar Assembly:

1.  Mount the flue collar to the top of the unit  as shown using the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and (3) weld  

  tabs provided in the parts box.

Room Air Deflector Assembly:

1.  Locate the Room Air Deflector.  Using the three(3) 1/2 Tek Screws provided, mount the deflector to the unit as   

  shown in the diagram.

Firebrick Configuration:

1.  Replace the Firebrick as shown in the illustration below.

Side view of flue collar

mount to heater top

Brick Configuration

HEATER

TOP

WELD 

TAB

5/16-18 x 1-1/2 

BOLT

2000

2500

Содержание 2000

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды