Countax D18/50 Скачать руководство пользователя | Manualshive

Страница: 22 / 24

background image

Page 22

Transmission -

Oil

TUFF TORQ K71 AXLE

Change transmission oil first time after 50 hours, then every 200
hours thereafter. Transmission oil should be a good quality 10W-
40 engine oil CE or CD rated. To change oil follow this
procedure:

• Remove the drain plug and drain oil (fig 4).

• After draining oil, thoroughly clean the drain plug then secure

and tighten the drain plug.

• Remove oil filter cap using a 3/8" drive extension socket.

• Remove oil filter and dispose.

• Fit new filter.

• Check condition of O-ring, replace if required.

• Lightly lubricate O-ring and replace on cap.

• Fit oil filter cap.

• Fill with fresh oil to specified level.

• Run the tractor with the transmission engaged for about 5

minutes and check the oil level again about 5 minutes later and
top up if low.

TRANSMISSION OIL LEVEL

The transmission oil reservoir is located behind drawbar plate at
rear of tractor. To inspect, remove drawbar plate and check.
Maximum oil level for transmission when cold 15mm in
reservoir (fig 3).

fig 2

fig 3

fig 1

‘O’ - Ring

Oil Filter

Transmission oil

reservoir

K71 Transmission

fig 4

Drain plug

«
...
20
21
22
23
24
»

Содержание D18/50

























Отзывы:

Нет отзывов

Похожие инструкции для D18/50

Бренд: LS tractor Страницы: 218

Бренд: Land Pride Страницы: 10

Бренд: Curtis Страницы: 10

Бренд: Komatsu Страницы: 4

Бренд: Komatsu Страницы: 8

Бренд: Kioti Страницы: 32

Бренд: New Holland Страницы: 2

Бренд: Daedong Страницы: 256

Бренд: TARAL Страницы: 102

Бренд: Kioti Страницы: 108

Бренд: Husqvarna Страницы: 60

Бренд: KNEGT Страницы: 111

Balebuster 2564

Бренд: Haybuster Страницы: 132

ROPAX RPM 7700 VII

Бренд: EPAX Страницы: 76

Бренд: Euro Shatal Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды