background image

 

Service Manual Pony Graphic

 

 

Chapter 1  

Introduction 

 

 

 

1.2 

1. Introduction 

This manual provides the basic procedures for the maintenance and the technical support of 
the Pony Graphic. Perform the service procedures described in this manual only if you are a 
trained and authorized COSMED service person. You must have a through knowledge and 
experience with medical electronic equipment. 
Pay attention to the directions in this service manual, along with the warning and cautions that 
appear throughout this manual.  
Read through each step in every procedure before beginning the repair. Always use the proper 
tools, test equipment and the most recent revision of this service manual.  
The Pony Graphic User’s Manual is an integral companion to this manual. Familiarize yourself 
with it before operating and repairing the equipment. 

1.1. 

Organisation of the manual 

This manual is organized as follows: 

Functional Description 

Provides a general description of the device, the theory of operation and the main usage 
modes. This chapter is useful to use the device in the most complete and proper mode. 

Part Description: 

Provides a detailed description of the device and the theory of operation of the modules. This 
chapter is useful to identify cause for problems and to operate properly. 

Maintenance 

Provides general specifications for maintenance and calibration. 

Trouble-shooting  

Trouble-shooting guidelines for detecting problems and  their respective solutions   

Service Procedures: 

Description of the adjustments and checks to carry out for a problem 

Schematics & Layouts 

A collection for drawing for disassembling of the parts, electric and pneumatic schematics, 
mounting planes and PCB Layouts 

Appendix A  

Technical information, replaceable part list, customer communication. 

1.2. Reference 

Documents 

The following document contains information that you may find useful for further reference as 
you read this manual: 
Pony Graphic: User’s Manual  P/N: C00296-02-91. 

1.3. Customer 

Communication 

COSMED would like to receive your comments and suggestions on its products and manuals. 
We are interested in your application with our products, and we would like to help you if you 
have problems with them. To make it easier for you to contact us, this manual contains our 
address and a Technical Support Form in the Appendix 
 
Our contact Address  
COSMED S.r.l, 
Via Dei Piani di Monte Savello, 37, P.O Box 3, Pavona di Albano, ROMA 
00040 ITALY. 
Voice  +39 (6) 931 5492 
Fax 

+39 (6) 931 4580 

Internet Web site: http://www.cosmed.it 

Содержание Pony graphic
























































Отзывы: