Cosen MT-105 Скачать руководство пользователя страница 7

If you need the assistance of qualified personnel for operations of 
extraordinary  maintenance,  or  in  the  case  of  repairs  under 
warranty is that later, always turn to an authorized service center, or 
directly to the factory, if in your region there aren't Service Centre.

6.2 ASSISTANCE

4. If the saw is not used for a long time please wipe blade and place,
if possible, in a place without humidity.
It is a good idea, in this case, loosen the blade does not maintain
unnecessarily tense.

When  it  is  necessary,  at  the  end  of  the  normal  operating  cycle, 
scrap the machine, it will be given to a center for the collection and 
disposal of hazardous chemicals in order to comply with standards 
for hygiene and environmental protection.

6.2 DISPOSAL OF THE MACHINE

7.0 TROUBLESHOOTING GUIDE

PROBLEM

POSSIBLE CAUSE

SUGGESTED REMEDY

Take the machine checked by skilled personnel; do 
not attempt to repair the engine alone.

Check the fuses and replace them if necessary.

Check the presence of voltage in the mains system.

Waiting for the normal reset thermal protector (few 
minutes) by releasing the start button.

Cut with less pressure.

Turn off the main red switch and restart with green 
light

Check tension of the blade (3.1)

Check the setting of the blade guide eccentric (3.6)

Check the setting of the blade guide (points 3.5 and 
3.6)

Check the cutting parameters (blade toothing, cutting 
speed) in the cuts table (point 4.6)

Decrease cutting pressure.

Check the positioning and clamping the part in the 
vice (point 4.5)

Check the tension of the blade (3.1)

Check the cutting parameters (blade toothing, cutting 
speed) in the cuts table (point 4.6)

Decrease cutting pressure.

Check the cutting parameters (blade toothing, cutting 
speed) in the cuts table (point 4.6)

Check that the air inlet port of the motor are free of 
obstacles.

Take the machine checked by skilled worker; do not 
attempt to repair the engine by yourself.

Make the cut with the right cutting pressure.

Carry out the calibration by loosening the fixing screws 
and repositioning the stops by specialized personnel.

Motor, cable or plug defective.

Fuses switchboard burned.

It  is  intervened  the  protector  Motor  over 
current.

Thermal protector of the motor.

No voltage in the mains system.

Excessive tension of the blade.

Incorrect  adjustment  of  the  blade  holder 
eccentrics pins.

Excessive  cutting  pressure  (on  pipes  and 
profiles).

Incorrect  blade  toothing  in  relation  to  the 
workpiece.

Incorrect  adjustment  of  the  eccentric  and 
sliding blade guide.

Wrong  placement  of  the  workpiece  in  the 
vice.

Poor blade tension.

Cutting speed is not correct in relation to the 
workpiece.

Excessive cutting pressure.

The blade is worn out or no teeth to suit the 
thickness of the piece being cut.

Engine overheating.

Motor overload caused by excessive cutting 
pressure

Motor failure.

The calibration of stops H (3.3) is not correct.

The motor does not work

The  blade  comes  out  from  the  blade 
older.

Imprecision in the square cut.

The finish of the cut is rough or wavy

The thermal protector has intervened

Imprecision of the cutting angle to 0 ° - 
45 °

Pag.7

Содержание MT-105

















Отзывы: