background image

 

 

 

 

© Corroventa Ltd. 

2020.04 

3 (17) 

 

Manufacture directive 

Condensing drier K5 HP PX is tested according to applicable directives and standards by Intertek.  

The dryer is CE labelled.  

Disclaimer 

 

Incorrect installation and/or incorrect use can cause damage to property as well as injury. 

 

The manufacturer assumes no liability for property damage or injury incurred as a result of 

failing to follow these instructions, the machine being used for purposes other than those 

intended or failure to observe these warnings. Such damage, injury or liability is not covered 

by the product warranty. 

 

The product warranty does not cover consumable parts or normal wear.  

 

The purchaser is responsible for checking the product upon delivery and before use to 

ensure it is in good condition. The product warranty does not cover damages resulting from 

the use of defective products.  

 

No changes or modifications to the machine may be performed without written consent  

from Corroventa Avfuktning AB. 

 

The product, technical data and/or installation and operating instructions are subject to 

change without notice.  

 

These user instructions contain information protected by applicable intellectual property 

laws. No part of these user instructions may be reproduced, stored in a retrieval system or 

transmitted to third parties in any form or by any means without the prior written consent of 

Corroventa Avfuktning AB. 

 

 

Any comments regarding the content of this document must be sent to: 

 

Corroventa Avfuktning AB   

Tel: +46 (0)36-37 12 00 

Mekanikervägen 3 

 

Fax +46 (0)36-37 18 30 

SE-564 35 Bankeryd 

 

E-mail: [email protected] 

Sweden 

 

 

 

 

 

 

 

 

Содержание K5 HP PX



















Отзывы: