CORNING Nano Power E62-N2RU страница 1 Скачать руководство пользователя | Manualshive

Страница: 1 / 43

background image

Installation Manual | CMA-794-AEN | Page 1

Nano Power (E62-N2)

Installation Manual

Everon™ 6200

This document describes the installation procedure for the E62-N2 remote unit.

This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and

QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC

License to operate this device. NOTE: Only authorized person can enter the area where the

antenna is installed. And the person is fully aware of the potential for exposure and can exercise

control over his or her exposure by leaving the area or by some other appropriate means.

Awareness of the potential for RF exposure in a workplace or similar environment can be provided

through specific training as part of a RF safety program.

GENERAL INFORMATION

The E62-N2RU is a low-power remote unit supporting cellular technologies on fiber optic
cable using the CPRI protocol. The N2 is ideal for multioperator multiband deployments of
cellular services in small-to-medium coverage areas. The N2 supports up to eight 20 dBm RF
channels. The N2 converts an optical signal to RF and then transmits at the relevant 3GPP
band and receives the analog RF signal, conditions it, and converts it back to optical for
routing to the E2 or A2.

1
2
3
...
»

Содержание Nano Power E62-N2RU












































Отзывы:

Нет отзывов

Похожие инструкции для Nano Power E62-N2RU

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: Value Point Страницы: 7

Бренд: Datalogic Страницы: 15

Бренд: ICP DAS USA Страницы: 4

Бренд: ICP DAS USA Страницы: 6

EIP-2000 Series

Бренд: ICP DAS USA Страницы: 19

Бренд: Kathrein Страницы: 16

Бренд: PACH & COMPANY Страницы: 4

Бренд: Rain Bird Страницы: 138

Бренд: ValvTechnologies Страницы: 20

Бренд: J+J Страницы: 4

Бренд: Val Controls Страницы: 6

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Gardigo Страницы: 6

Бренд: VAT Страницы: 14

Бренд: Jäger Страницы: 18

Бренд: Warner Electric Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды