3
2
Safety Precautions
◗
◗
Never
use the microcentrifuge in any manner not specified in these
instructions.
◗
◗
Never
operate the microcentrifuge without a rotor properly attached to
the shaft.
◗
◗
Never
fill tubes while they are in the rotor. Liquid spillage may harm the
unit.
◗
◗
Never
put hands in the rotor area unless the rotor is completely stopped.
◗
◗
Never
move the microcentrifuge while the rotor is spinning.
◗
◗
Never
use solvents or flammables near this or other electrical equipment.
◗
◗
Never
centrifuge flammable, explosive, or corrosive materials.
◗
◗
Never
centrifuge hazardous materials outside of a hood or proper
containment facility.
◗
◗
Never
try to continue operating the microcentrifuge if the microcentrifuge
stops working prematurely. Stop the microcentrifuge immediately by
turning off the main power switch on the back side of the microcentrifuge.
Wait one minute before turning on the main power switch to operate the
microcentrifuge again.
◗
◗
Always
load the rotor symmetrically. Each tube should be counter balanced
by another tube. Weight of individual tubes may not exceed 3.0 g.
◗
◗
Always
place the microcentrifuge within easy access to an electrical outlet.
◗
◗
Always
use only microcentrifuge tubes made from plastic and designed
to withstand centrifugal forces of at least 2,000 x g.
Cleaning
Before using any cleaning or decontamination methods other than those
recommended by the manufacturer, check with the manufacturer that
the proposed method will not damage the equipment. To clean the micro-
centrifuge, use a damp cloth and a mild, noncorrosive detergent (pH <8).
After cleaning, ensure all parts are dried thoroughly before attempting
to operate the unit. Do not immerse the microcentrifuge in liquid or pour
liquids over it.
Questions and Service
Should you have a question about the microcentrifuge or required service
for the unit, please use the contact numbers listed. Do not send a unit for
service without first calling to obtain a repair authorization (RA) number
and a decontamination form. Should the microcentrifuge require service,
be sure to decontaminate it and enclose the decontamination form. The
unit should be properly packed to avoid damage. Any damage resulting
from improper packaging shall be the responsibility of the user.
Operation
Before operating the microcentrifuge, be sure that the power switch on the
back of the unit is in the “on” position. To begin a run, simply close the lid
of the microcentrifuge. No other controls are required.
◗
◗
Fast Stop:
Press down and release the tab on the front of the lid. This will
release the lid lock, allowing the lid to open and the rotor to come to a
fast braked stop.
◗
◗
Gradual Stop:
Put the power switch in the “off” position, this will cut
power to the motor and the rotor will come to a gradual stop.
Caution:
Do not attempt to open the lid or remove samples until the unit
has come to a complete stop. Once the lid has fully opened and the rotor
has stopped, samples may be removed from the rotor.
Safe operation of the microcentrifuge requires that the rotor be loaded in
a balanced fashion. Failure to load the rotor properly presents a hazardous
condition and may damage the microcentrifuge. Individual tubes, strip tubes,
and/or adapters must always be loaded symmetrically to ensure proper
balance. Never run the microcentrifuge with only one individual tube or
strip tube in place.
Equipment Maintenance
The microcentrifuge should be cleaned periodically. Ensure that the unit is
not plugged in. Use a damp cloth and a mild, noncorrosive detergent (pH <8).
Do not immerse the microcentrifuge in liquid or pour liquids over it. Excessive
amounts of liquid should be avoided. Liquid should not come in contact
with the motor. After cleaning, ensure all parts are dried thoroughly before
attempting to operate the unit.
Rotors
The microcentrifuge is supplied with two interchangeable quick release
rotors. No tools are required to exchange the rotors or attach them to
the motor shaft. The rotors can be easily exchanged with one hand by
way of the quick release system. Removal of the rotors is done by placing
your thumb on top of the motor shaft and lifting up with two fingers
underneath the rotor. Place the other rotor into position on the motor shaft
and snap in.
8 place tube rotor
4 place strip rotor
