CORNING Everon 6000 Скачать руководство пользователя страница 59

Страница: 59 / 75

User Manual v1.0

Corning Restricted and Confidential Proprietary - Controlled content

UM - Everon 6000 DAS - 19-DEC-2020.docx| December 2020

|Page 59 of 170

2.3.9

Connect Power & POWER UP

The MRU PSM is located on the bottom right of the chassis front. The PSM type (AC/DC) is model dependent.

•

Refer to section 2.4.7.1 for AC models.

•

Refer to section 2.4.7.2 for DC models

2.3.9.1

AC models

WARNING! Approved power cable

–

the

entire length of the power cable (or flexible cord) and

the insulation must be intact. The cable must be firmly connected to both the electrical plug and
the unit itself.

Standard plug

–

the use of a standard plug is mandatory. The use of a non-standard power plug

can cause electrocution! Also, plugging a non-standard plug into a standard socket that does not

correspond to the plugs’ shape, can damage the socket

making it a safety hazard

AC Power Connection

Connect the MRU power connector to the AC power source using the provided AC power cable:

•

Power input: 100-240 VAC/50-60 Hz

•

Power consumption: 620 W (maximum)

•

Maximum AC current consumption: 7 A

Содержание Everon 6000












































































Результаты поиска

Содержание Everon 6000

Отзывы:

Похожие инструкции для Everon 6000

Бренды по названию

Популярные бренды

CORNING Everon 6000, Руководство пользователя

Результаты поиска

Содержание Everon 6000

Отзывы:

Похожие инструкции для Everon 6000

Бренды по названию

Популярные бренды