Cornelius SPIRE 4.1 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 14

Cornelius SPIRE 4.1 Скачать руководство пользователя страница 2

Manual Installation Conversion Kit 4.1 To 4.2

Publication Number: 629097805INS

- 2 -

©2019, Cornelius Inc.

Q

UALIFIED

S

ERVICE

P

ERSONNEL

!

WARNING:

Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.

All wiring and plumbing must conform to national and local codes. Failure to comply could result in serious injury,
death or equipment damage.

S

AFETY

P

RECAUTIONS

!

WARNING:

Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all
power is off to the unit before performing any work. Failure to comply could result in serious injury, death or damage to
the equipment.

CAUTION:

!

Always be sure to keep the area around the unit clean and free of clutter. Failure to keep this area clean may result in
injury or equipment damage.

CAUTION:

!

Note the following: This unit is not designed for use in outdoor locations. The appliance must be placed in a horizontal
position. The appliance is not suitable for installation in an area where a water jet would be used.

«
1
2
3
4
...
»

Содержание SPIRE 4.1















Отзывы:

Нет отзывов