CopyPro PowerPro II страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 60

background image

PowerPro II

28

CopyPro PowerPro II

Figure 15:

Printhead cleaning with ribbon removed

Printhead Cleaning Procedure

•

If tray is in, press Tray Button to extend tray

•

Remove the top cover by carefully lifting and pulling forward. Set the cover aside.

•

Open printer chassis by: Pulling chassis release knob and lifting chassis up by chassis
handle

•

Remove Ribbon Supply Roller from printer and place on CD Tray, this will expose
the printhead. (As an alternative remove ribbon completely from printer)

•

Printhead is now visible from the inside of Printer chassis

•

Move the Supply Ribbon roller and ribbon forward and away from the front of the
unit, exposing the printhead.

•

Use a cotton swab or Q-tip with a few drops of isopropyl alcohol to gently rub the
printing surface of the print head.

•

Use a sweeping motion starting from one end of the printhead to past the other end to
remove any dust particles (do not lift up Q tip in middle of printhead since that may
leave residue in that area)

•

Allow the printhead a minute to dry before moving ribbon spindle back on to chassis

•

Printer will wind slack ribbon at power ON, or pressing Start and Tray button
simultaneously will also wind slack ribbon

Chassis Release
Button is located
inside case

«
...
26
27
28
29
30
...
»

Содержание PowerPro II





























































Отзывы:

Нет отзывов

Похожие инструкции для PowerPro II

Бренд: Rimage Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды