Cooper Elpro 450U-E Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 85

Cooper Elpro 450U-E Скачать руководство пользователя страница 73

Elpro Technologies 450U-E Wireless Ethernet Modem & Device Server User Manual

Rev Version 1.0.12-Beta7

www.cooperbussmann.com/wirelessresources

73

The drive should contain only one partition, and the Offset value should be non-zero as shown below.

DISKPART> list partition
  Partition ###  Type         Size     Offset
  -------------  ----------------  -------  -------
  Partition 1   Primary         1910 MB   64 KB

You can now
format the drive using the diskpart utility.

If the

or if there is more than one Partition, as indicated in the examples below, follow steps 6 and

7 below to re-configure the drive.

Partition ###  Type          Size    Offset
  -------------  ----------------  -------  -------
Partition 1   Primary        1911 MB     0 B

Partition ###  Type          Size    Offset
-------------  ----------------  -------  -------
Partition 1   Primary         100 MB   64 KB
Partition 2   Primary        1810 MB   101 MB

6.

DISKPART> list disk
  Disk ###  Status       Size     Free    Dyn  Gpt
  --------  -------------  -------  -------  ---  ---
  Disk 0   Online        232 GB      0 B
* Disk 1   Online       1911 MB      0 B

DISKPART> clean
DiskPart succeeded in cleaning the disk.
DISKPART> list disk

  Disk ###  Status       Size    Free    Dyn  Gpt
  --------  -------------  -------  -------  ---  ---
  Disk 0   Online        232 GB      0 B
* Disk 1   Online       1911 MB  1910 MB

7.

command, and note that there is only one partition, and that the offset is non-zero.

DISKPART> create partition primary
DiskPart succeeded in creating the specified partiti
Type          Size    Offset
  -------------  ----------------  -------  -------
* Partition 1   Primary         1910 MB   64 KB

8.

Finally, the drive can be formatted using the diskpart command line. The file system format should be selected

w the label

«
...
71
72
73
74
75
...
»

Содержание Elpro 450U-E






















































































Отзывы:

Нет отзывов