Cooper Sound CS 208 V2 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 39

Cooper Sound CS 208 V2 Скачать руководство пользователя страница 26

MODEL CS 208 v2

MAY 2003

OPERATIONAL & APPLICATION NOTES

24

T/D (tape, direct):

Tape return to monitor 1.

Comm. in:

Comm. return level controlled by trimmer below.

‘PL’:

Assigns PL to monitor 1 (Down = on)

Phones select:

M = Mono
ST = Sereo
MS = Mid Side

Monitor
pots 1, 2, 3:

To adjust level to phones 1, 2, 3 (stereo output). Caution: It is recommended to
set the ‘phones’ pot at minimum before wearing headphones. Then increase the

level to suit personal preference. The minimum total load (impedance) per side is

25

Ω

. The (2) phones 1 jacks are in parallel, the combined load should not be less

than 25

Ω

.

Meters Section:

Tape/Dir.:

Tape, Direct to the meters

Meters 1, 2:

Monitor AB channels (tape or direct) or PFL.

Meters 3, 4:

Monitor either CD (tape or direct) or A1, A2.

(Also, Meter 4 can indicate the battery level. See meter bridge)

PFL momentary
switch:

Meter 1 & 2 monitor the PFL signal selected on the input channels.

VU Meter:

Responds to the average program level. The internal oscillator should be set for

‘0’ VU on the meter. This will correspond to +4 dBu on the XLR outputs. As this

is an average responding meter, the peak program level will not be indicated.
In general, the Nagra modulometer will indicate approximately ‘0’ dB for peak
levels if the line up tone is set at -8 dB modulometer. For feeding external
equipment with VU meters, the level should be set for ‘0’ VU on both the mixer
and the outboard equipment.

PPM Meter:

Peak responding meter. The reference level for a 1 kHz sine wave is set for -8
dB. This corresponds to approximately ‘0’ VU, although the difference between
an average responding meter and a PPM meter will vary according to program
material. The rise and fall times are set to approximate the Nagra modulometer meters.

Output Faders:

These faders should be left at the maximum position (ie: ‘0’) for optimum
headroom. All line-up tones etc., should be made with the faders in this position.

Return Trimmers:

To adjust return levels to the phones and meters.

«
...
24
25
26
27
28
...
»

Содержание CS 208 V2








































Отзывы:

Нет отзывов