Cooper Lighting WaveLinx Lite Скачать руководство пользователя страница 5

Страница: 5 / 78

User Manual: WaveLinx Lite (1.5)

www.cooperlighting.com

Welcome and Introduction

WaveLinx Lite (1.5) offers wireless control without the need of a centralized controller for outdoor and indoor applications. Outdoor

applications including parking garages, decks, and surrounding areas while indoor applications include office, education, healthcare, hospitality,

retail, industrial, and manufacturing. WaveLinx Lite provides a quick method to achieve code-compliance without extra wiring or complicated

commissioning.
This manual provides an overview of the WaveLinx Lite System. Use this manual to:

•

Understand the architecture of the WaveLinx Lite System, page 5

•

Understand the expected behavior for WaveLinx Lite System devices, page 6

•

Install the WaveLinx Lite Mobile Application, register the cloud portal, and login, page 13

•

Set up a site, organizing devices into areas and zones and assigning occupancy sets, page 18

•

Modify the default operation of areas, zones, devices, wallstation operation, occupancy sets, daylight sets, and scenes, page 29

•

Use the mobile application to issue commands and view device details, page 56

•

Perform administrative tasks; including resetting passwords, editing site details, performing backups and restores, transfer site ownership,

update firmware and the mobile application, page 63

•

Perform basic troubleshooting to resolve communication errors, use the device scan feature, replace devices, perform factory resets and

perform advanced daylight calibration, page 71

WaveLinx Lite Architecture and General Rules

The WaveLinx Lite architecture uses Bluetooth

mesh networking for a reliable and secure communication between devices. The WaveLinx Lite

Mobile Application uses the mobile device’s Bluetooth connection to communicate and configure WaveLinx Lite devices. The Mobile App uses

an internet connection to communicate to a secure cloud portal to store and backup site programming.

Содержание WaveLinx Lite















































































Результаты поиска

Содержание WaveLinx Lite

Отзывы:

Cooper Lighting WaveLinx Lite, Руководство пользователя и программирования, Страница: 5 / 78

Результаты поиска

Содержание WaveLinx Lite

Отзывы: