2
NOTE:
Coverplate mounts to recessed mounted
standard junction boxes (Fig. 2). Junction box must be
at least 1-1/2 in. in depth for proper installation for
recessed mount application.
1.
Install protective reflectors (I) onto lampholders
by lining up the nipples on the covers, over the
lampholder slots. Lock into place by twisting
covers counterclockwise (Fig. 3).
2.
Line up the holes on the mounting bracket (H) with
the holes on your junction box. Using either (2) #6
screws or (2) #8 screws (D) (depending on the
size of the holes in your junction box), attach the
mounting bracket (H) to your junction box (Fig. 4).
3.
Thread fixture wires through coverplate gasket (B).
4.
Connect copper colored ground wire (coming from
the fixture coverplate) to the house ground wire
using wire nut (E) provided. Connect fixture black
wire to house black wire, fixture white wire to house
white wire using wire nuts (E) provided (Fig. 5).
5.
Attach fixture (A) to the mounting bracket (H) using
the center bolt (G) provided. Be sure no loose wires
remain sticking out from underneath the coverplate.
Insert plastic color-matched plug (F) in center bolt
hole for finished appearance (Fig. 6).
6.
Apply silicone caulking around edges of coverplate
and in any open holes to provide a watertight seal
from rain and moisture.
7.
Insert lampholder gaskets (C) into lampholder
assembly, tightly against lampholder, and screw
bulbs into each lampholder (Fig. 7). (Do not
overtighten bulbs.)
8.
Turn on power at mainfuse/breaker box.
OPERATING YOUR FIXTURE
1.
Move slide switch on bottom of the sensor to
“TEST”. Set sensitivity slide switch to medium
or “M” (Fig. 8).
2.
Turn on the power to fixture. Allow fixture to warm
up approximately 90 seconds before testing. (Lights
may or may not come on during warm-up period;
this is normal.)
3.
Aim sensor head in desired position.
NOTE:
Maintain air spacing between lamps and sensor
head, at least 1 in. Make sure sensor head is positioned
with control switches facing towards the ground.
4.
Walk across the detection zone at the farthest
distance you wish your detector to detect motion.
5.
Adjust sensitivity until you get desired results.
For more range, aim sensor head slightly upwards.
For less range, aim sensor head slightly downward.
6.
Move slide switch to 4 min or 12 min (AUTO mode),
or to one of the three “Night Time On” settings. At
dusk, lights will operate in the “AUTO” or “Night
Time On” settings.
Mode of
MODE Knob
How to Set
Operation
Adjustment
Power Switch
Test Setting
Lights should turn ON with
motion both day and night.
Lights should turn OFF
after 4 seconds.
Keep the power
to the fixture ON.
TEST
Motion Activated
(“Auto” Setting)
Lights should turn ON with
motion only at night and should
turn off after 4 or 12 min.
of no motion.
AUTO 4 MIN
or
AUTO 12 MIN
Keep the power
to the fixture ON.
Dusk-to-Dawn Setting
Override Mode
(activated only at night)
Lights should stay ON 100%
brightness from dusk to dawn and
then reset to the “AUTO” or “Night
Time On” setting at next dawn.
AUTO 4 MIN
or
AUTO 12 MIN
or
ALL “NIGHT TIME ON” MODES
Turn the power
OFF-ON-OFF-ON
within 3 seconds.
Fig. 2
Octagonal
Round
1-1/2 in.
ENERGY STAR
®
To meet ENERGY STAR
®
requirements, the photosensor control knob must be in the
“Auto” mode to prevent operation during full daylight. Maximum lamp wattage can not
exceed 250 watts.
SELECTING YOUR DESIRED FEATURE
Return to “Auto”
or “Night Time On” Settings
(motion activated)
from any of the above settings.
AUTO 4 MIN
or
AUTO 12 MIN
or
ALL “NIGHT TIME ON” MODES
Turn the power OFF
for at least 90 seconds
and then back ON.
Continuous Override Mode
(Standard Floodlight Setting)
Lights should stay ON
continuously both day and night
(must be reset manually).
TEST
Turn the power
OFF-ON-OFF-ON
within 3 seconds.
ENERGY STAR
®
is sponsored by the U.S.
Environmental Protection Agency & U.S.
Department of Energy.
Visit www.energystar.gov to learn more.
D
H
D
Fig. 4
2 Hour
NIGHT TIME ON
then Motion Activated
Lights should turn ON
automatically at night 100%
brightnes for 2 hours, then reset
to regular auto motion settings for
the remainder of the evening.
NIGHT TIME ON
2 HR
(2 Hours)
Note:
Once the light has come
ON in the selected “Night Time
On” mode, you cannot change
the mode setting until the next
dawn. The light will operate in
the first “Night Time On” mode
selected (2 hour, 4 hour, 6 hour)
even if changed.
Keep the power
to the fixture ON.
4 Hour
NIGHT TIME ON
then Motion Activated
Lights should turn ON
automatically at night 100%
brightnes for 4 hours, then reset
to regular auto motion settings for
the remainder of the evening.
NIGHT TIME ON
4 HR
(4 Hours)
Note:
Once the light has come
ON in the selected “Night Time
On” mode, you cannot change
the mode setting until the next
dawn. The light will operate in
the first “Night Time On” mode
selected (2 hour, 4 hour, 6 hour)
even if changed.
Keep the power
to the fixture ON.
6 Hour
NIGHT TIME ON
then Motion Activated
Lights should turn ON
automatically at night 100%
brightnes for 6 hours, then reset
to regular auto motion settings for
the remainder of the evening.
NIGHT TIME ON
6 HR
(6 Hours)
Note:
Once the light has come
ON in the selected “Night Time
On” mode, you cannot change
the mode setting until the next
dawn. The light will operate in
the first “Night Time On” mode
selected (2 hour, 4 hour, 6 hour)
even if changed.
Keep the power
to the fixture ON.
Fig. 6
F
G
A
Fig. 5
Wall mount
Eave mount
B
A
A
E
E
E
Fig. 3
I
A
Fig. 7
C
C
Fig. 8
MODE
TEST
4 MIN
12 MIN
2 HR
4 HR
6 HR
SENSITIVITY
H
M
L
AUTO
NIGHT TIME ON
1-1/2 in.