Cooper Lighting DLC-PDC Скачать руководство пользователя страница 3

INTRODUCTON 

1.1 

General 

Please read these instructions carefully to prevent any possible injury or equipment damage. For 
installation of the product, the installer must be a qualified and experienced technician. Prior to any 
installation, inspect the panel for damage and verify the product ratings to confirm that this product 
will satisfy your requirements and application. 

The DLC-PD Sensor is a generic term used throughout this document to describe all variations of the 
sensor including but not limited to the indoor, outdoor, atrium, and skylight types. 

1.2 

Overview 

The DLC-PDC Photodiode Controller automatically switches a dry contact in response to change in 
natural daylight.  The DLC-PDC provides a maintained single pole, double-throw relay output to drive 
electrically held contactors or relays, or has the ability to provide inputs to Energy Management 
Systems (EMS).  The DLC-PDC can control incandescent, fluorescent or HID lighting.  The low 
voltage controller requires a remotely mounted DLC-PD sensor.  The DLC-PDC controller provides 
Low and High setpoints, with a deadband to eliminate nuisance or intermittent changes. 

Содержание DLC-PDC














Отзывы: