15
Technical Information
Service Manual
Press this button, the unit will be turned on, press it once more, the unit will be turned off. When turning on or turning off the unit, the
Timer, Sleep function will be canceled, but the presetting time is still remained.
2
. MODE Button
Press this button, Auto, Cool, Dry, Fan, Heat mode can be selected circularly. Auto mode is default while power on. Under Auto mode, the
temperature will not be displayed; Under Heat mode, the initial value is 28
℃
(82
℉
); Under other modes, the initial value is 25
℃
(77
℉
).
3
. - Button
Presetting temperature can be decreased. Press this button, the temperature can be set up, continuously press this button and hold for
two seconds, the relative contents can quickly change, until unhold this button and send the order that the
℃
(
℉
) signal will be displayed
all the time. The temperature adjustment is unavailable under the Auto mode, but the order can be sent by if pressing this button.
3
. + Button
For presetting temperature increasing. Press this button, can set up the temperature, when unit is on. Continuously press and hold this
button for more than 2 seconds, the corresponding contents will be changed rapidly, until unpress the button then send the information,
℃
(
℉
) is displlaying all along. In Auto mode, the temperature can not be set up, but operate this button can send the signal. Centigrade
setting range: 16-30; Fahrenheit scale setting range 61-86.
4
. FAN Button
Press this button, Auto, Low, Middle, High speed can be circularly selected. After powered on, Auto fan speed is default.
Note: Under the Dry mode, the fan speed isn't adjustable, low fan speed is imperative, but when operating this button, the wireless
adjustable, low fan speed is imperative.
5
. Button
Press this button, to set up swing angle, which circularly changes as below:
This is an universal use remote controller. If remote controller sends the following three kinds of status that the swing status of main unit
will be:
When the guide louver start to swing up and down, if turn off the Swing, the air guide louver will stop at current position. which
indicates the guide louver swings up and down between that all five positions.
6
. CLOCK Button
Press this button, the clock can be set up, signal
blink and display. Within 5 seconds, the value can be adjusted by pr or -
button, if continuously press this button for 2 seconds above, in every 0.5 seconds, the value on ten place of Minute will be increased
1. During blinking, repress the Clock button, signal
will be constantly displayed and it denotes the setting succeeded. After powered
on,12:00 is defaulted to display and signal
will be displayed. If there is signal
be displayed that denotes the current time value is
Clock value,otherwise is Timer value.
7
. TIMER ON Button
Timer On setting: Signal “ON” will blink and display, signal
will conceal, the numerical section will become the timer on setting status.
During 5 seconds blink, by pr or will be increased or decreased 1 minute. Hold pr or - button, 2 seconds later, it in the
one place of minute, then the one place is constant, ten numbers change in the tens place of minute at 2.5 seconds speed and carry.
During 5s blink, press the Timer button, the timer setting succeeds. The Timer On has been set up, repress the timer On button, the
Timer On will be canceled. Before setting the Timer, please adjust the Clock to the current actual time.
7
. TIMER OFF Button
Once press this key to enter into TIMER OFF setup, in which case the TIMER OFF icon will blink. The method of setting is the same
as for TIMER ON.
8
. X-FAN Button
Pressing X-FAN button in COOL or DRY mode, the icon
is displayed and the indoor fan will continue operation for 10 minutes in
order to dry the indoor unit even though you have turned off the unit. After energization, X-FAN OFF is defaulted. X-FAN is not available
AUTO
COOL
DRY
FAN
HEAT
