Coolmay CX-WIFI-2NET Скачать руководство пользователя страница 39

Страница: 39 / 93

Shenzhen Coolmay Technology Co.,Ltd

CX-WIFI-2NET module user manual

Page

, Total 93 pages

www.coolmay.com

Above is the AT command setting through the serial port, and the AT

command can also be set through WIFI.

First, the computer establishes a network connection with the module, using

the USR-WIFI232-Setup setting software provided on the CD.

Through the network operation, click "Search", the searched module will be

displayed, click it and set AT command on the left operation area. (same way as

the serial port setting).

3.2.2.1 Command format

AT+ command adopt ASCII-based command line, command format as below:

Format description
< >: indicates the part that must be included
[ ]: indicates an optional part

Command message

AT+<CMD>[op][para-1,para-2,para-3,para-

4…]<CR>

AT+

：

Command message prefix

CMD

：

Command string

Содержание CX-WIFI-2NET






























































































Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды

Coolmay CX-WIFI-2NET, Руководство пользователя

Результаты поиска

Содержание CX-WIFI-2NET

Отзывы:

Похожие инструкции для CX-WIFI-2NET

Бренды по названию

Популярные бренды